活动 - FORD LDM Localization - Redmine

活动

从 2024-10-19 到 2024-10-28

2024-10-28

20:23 功能 #2760 (已关闭): Ford_SWER_0044_0002： FAN Functional self-test when power on for app: App:
The software needs to determine whether a fan self-test is required and the duration of the self-test based on ... 涛陆
20:20 功能 #2759 (已关闭): Ford_SWER_0044_0001： FAN Functional self-test when power on for dataset: Dataset:
‘FanRunTime_OnPwr_cfg’ definition:
• 0x00: 0s
• 0x01: 20s
• 0x02: 40s
• 0x03: 60s 涛陆
20:13 功能 #2758 (已关闭): Ford_SWER_0045_0003：NTC Temperatur Triggle Fan For Dataset: ‘Fan_Activation_Temp_cfg’ definition:
• Range: 50℃ to 100℃
• Resolution: 5℃ 涛陆
20:12 功能 #2757 (已关闭): Ford_SWER_0045_0002：NTC Source Triggle Fan For Dataset: Dataset:
If ‘FAN_Activation_Trigger_cfg’ = 0x02 which means FAN will be activated when the temperature is more than ... 涛陆
20:11 功能 #2756 (已关闭): Ford_SWER_0045_0001：Activation of the Fan For Dataset: Dataset:
The activation of FAN can be configured by the parameter ‘FAN_Activation_Trigger_cfg’.
• 0x00: No fan
• 0... 涛陆
19:59 功能 #2755 (已关闭): Ford_SWER_0046_0002：Fan Failure Detection Of App: the software will sample the feedback line(C16) of the fan.
|State of the Fan Feedback Line |AD Range |Operati... 涛陆
19:50 功能 #2754 (已关闭): Ford_SWER_0046_0001：Fan Failure Detection Of Dataset: Dataset has‘Fan_Outage_Detect_cfg’to determine either perform full stall/outage detection or not.
‘Fan_Outage_Detect... 涛陆
19:18 功能 #2753 (已关闭): Ford_SWER_0047_0001：LED Thermal Derating Peak Current morn than 150mA: If the current derating is more than 150mA,the LDM shall control the LED junction temperature by controlling the curr... 涛陆
19:09 功能 #2752 (已关闭): Ford_SWER_0048_0002：Output Channel Thermal Monitoring NTC Source Select For App: App：
Reduce or not reduce power by obtaining information from 'Channelx_NTC_Source_cfg' and combining it with the co... 涛陆
19:03 功能 #2751 (已关闭): Ford_SWER_0048_0001：Output Channel Thermal Monitoring NTC Source Select For Dataset: Dataset：
‘Channelx_NTC_Source_cfg’ definition:
• 0x00: NOT USED
• 0x01: NTC1
• 0x02: NTC2
• 0x03: NTC3
• 0x04: ... 涛陆
18:56 功能 #2750 (已关闭): Ford_SWER_0049_0002：Output Thermal Derating Curve For App: APP:
1.软件初始化时候计算每两个降功率点之间的斜率
2.任务循环里面滤波并计算当前温度值，判断当前温度处于哪一档区间，用该档的斜率计算目标降功率的值
3.当前输出降功率值和目标降功率的值不一致的时候做缓慢变化
4.如果降... 涛陆
18:53 功能 #2749 (已关闭): Ford_SWER_0049_0001：Output Thermal Derating Curve Dataset Configure: Dataset：
NTC derating temperature range and resolution setting:
‘CHx_NTC_TempDerate1_cfg’: should always be -40℃ an... 涛陆
18:40 功能 #2748 (已关闭): Ford_SYER_0050_0006：LDM Internal Thermal Derating Hysteresis: Derated functions shall recover to performance of the previous range with a 5°C hysteresis.
模块温度降功率回到上一个区间的状态需要增加5℃的回滞涛陆
18:38 功能 #2747 (已关闭): Ford_SYER_0050_0005：LDM Internal Thermal Derating for SBL: If LDM Internal temperature is over 125℃，SBL target Derating value should be 20%.
If LDM Internal temperature is ove... 涛陆
18:36 功能 #2746 (已关闭): Ford_SYER_0050_0004：LDM Internal Thermal Derating for DRL/PL: If LDM Internal temperature is over 135℃，DRL/PL target Derating value should be 20%.
If LDM Internal temperature is ... 涛陆
18:32 功能 #2744 (已关闭): Ford_SYER_0050_0003：LDM Internal Thermal Derating for Turn Indicator: If LDM Internal temperature is over 145℃，Turn target Derating value should be 20%.
If LDM Internal temperature is un... 涛陆
18:29 功能 #2743 (已关闭): Ford_SYER_0050_0002：LDM Internal Thermal Derating for HB: If LDM Internal temperature is over 125℃，HB target Derating value should be 20%.
If LDM Internal temperature is over... 涛陆
18:25 功能 #2573 (已解决): Ford_SYSR：FS_REQ0053_V2 General LED Failure Detection: 槐杨
18:24 功能 #2742 (已关闭): Ford_SYER_0050_0001：LDM Internal Thermal Derating for Foreground LB: start derating at 135℃ 100% to 145℃ 20% (linear) 涛陆
18:22 功能 #2741 (已关闭): Ford_SWER_0062_0005：LDM diagnostic with test command——Write MEC: 发送诊断写数据：（NAD）04 2E F1 A0 MEC
反馈显示写入成功或失败槐杨
18:19 功能 #2740 (已关闭): Ford_SWER_0062_0004：LDM diagnostic with test command——Read Daataset 数据: 发送诊断数据：（NAD）03 22 C0 C1
反馈显示Dataset数据信息：如通道配置，LSD配置，FAN配置，NTC配置等，具体信息见附件槐杨
18:16 功能 #2739 (已关闭): Ford_SWER_0062_0003：LDM diagnostic with test command——Read SW Version: 发送诊断数据：（NAD）03 22 C0 C0
SW Version 显示软件版本信息：如程序版本，Dataset版本，项目版本等，具体信息见附件槐杨
18:13 功能 #2738 (已关闭): Ford_SWER_0062_0002：LDM diagnostic with test command——Read EDF2: 发送诊断数据：（NAD）03 22 C0 C3
EDF2 显示实时信息：如诊断帧信息，降功率数据，Lifetime，和最近5次的故障信息等，具体信息见附件槐杨
18:09 功能 #2737 (已关闭): Ford_SWER_0062_0001：LDM diagnostic with test command——Read EDF1: 发送诊断数据：（NAD）03 22 C0 C2
EDF1 显示实时信息：如通道电流，电源电压，升压电压，通道Vf， Rbin电阻范围，内部和外部温度等，具体信息见附件槐杨
17:46 功能 #2736 (已关闭): Ford_SWER_0061_0005：Failure Recover strategy—— Power Reset: 本章所述的所有LDM故障应在以下情况下恢复：
ldm上电复位
All the LDM failure above in this chapter shall recovery when:
LDM power on re... 槐杨
17:45 功能 #2735 (已关闭): Ford_SWER_0061_0004：Failure Recover strategy—— LIN Rcv: 本章所述的所有LDM故障应在以下情况下恢复：
ldm在500毫秒内接收3个有效的LIN信号
All the LDM failure above in this chapter shall recovery when:
... 槐杨
17:44 功能 #2734 (已关闭): Ford_SWER_0061_0003：Failure Recover strategy——Buck Flt Rcv: 本章所述的所有LDM故障应在以下情况下恢复：
buck通道短/开路故障恢复，自恢复
All the LDM failure above in this chapter shall recovery when:
Bu... 槐杨
17:42 功能 #2733 (已关闭): Ford_SWER_0061_0002：Failure Recover strategy——RBIN/NTC Rcv: RBIN不可自恢复，需要重新上电；
NTC可以自恢复。槐杨
17:41 功能 #2732 (已关闭): Ford_SWER_0061_0001：Failure Recover strategy——LED Rcv: 本章所述的所有LDM故障应在以下情况下恢复：
•led负载恢复正常工作
All the LDM failure above in this chapter shall recovery when:
LED load re... 槐杨
17:35 功能 #2731 (已关闭): Ford_SWER_006x_0004：LB hardwire activate lost failure - LB Hardwire ON + Headlamp_Low_Beams_Out Off: 目前采用LB硬线作为激活信号，当出现意外的硬线丢失时，LDM应在LB硬线激活状态与LIN信号“Headlamp_Low_Beams_Out”ON状态不匹配时报告LB硬线输入故障报告，且只有当“Headlamp_Low_Beams_... 槐杨
17:33 功能 #2730 (已关闭): Ford_SWER_006x_0003：LB hardwire inactive and Headlamp_Low_Beams_Out ,LB shall OFF: 目前采用LB硬线作为激活信号，当出现意外的硬线丢失时，LDM应在LB硬线激活状态与LIN信号“Headlamp_Low_Beams_Out”ON状态不匹配时报告LB硬线输入故障报告，且只有当“Headlamp_Low_Beams_... 槐杨
17:27 功能 #2729 (已关闭): Ford_SWER_0063_0001：LDF: 在BCM LIN（10417波特率）上，LDM应使用“LDF BCM_G2_LIN_05_Ckt_v17_2016Dec01.LDF”
The LDM shall consider LDF BCM_G2_LIN_05_Ckt_v... 槐杨
17:07 功能 #2728 (已关闭): Ford_SWER_006x_0002：If either LB hardwire status and Headlamp_Low_Beams_Out ON status is ON,then LB Function shall ON: 槐杨
17:01 功能 #2727 (已关闭): Ford_SWER_006x_0001：LDM shall report the LB Outage while LB hardwire status and Headlamp_Low_Beams_Out ON status mismatch within1000ms: 目前采用LB硬线作为激活信号，当出现意外的硬线丢失时，LDM应在LB硬线激活状态与LIN信号“Headlamp_Low_Beams_Out”ON状态不匹配时报告LB硬线输入故障报告，且需1000ms报告。
关联Open is... 槐杨
16:58 功能 #2645 (已解决): Ford_SWER_0013_0006：Channel 2 to 4 Functional Configuration（TI）: 培源左
16:57 功能 #2644 (已解决): Ford_SWER_0013_0005：Channel 2 to 4 Functional Configuration（DRL）: 培源左
16:57 功能 #2726 (已关闭): Ford_SWER_0086_0009: MEC change: MEC值更新后,需要上位机通过$11服务复位LDM方可更新输出状态盛炜朱
16:56 功能 #2725 (已关闭): Ford_SWER_0086_0008: CANOE change MEC: MEC值更新后,需要上位机通过$11服务复位LDM方可更新输出状态,$11服务自动跟在$2E服务后,无需再次点击. 盛炜朱
16:56 功能 #2643 (已解决): Ford_SWER_0013_0004：Channel 2 to 4 Functional Configuration（HB）: 培源左
16:55 功能 #2642 (已解决): Ford_SWER_0013_0003：Channel 2 to 4 Functional Configuration（LB）: 培源左
16:54 功能 #2641 (已解决): Ford_SWER_0013_0002：Channel 2 to 4 Functional Configuration（Not used）: 培源左
16:52 功能 #2640 (已解决): Ford_SWER_0013_0001：Channel 2 to 4 Functional Configuration（Dataset配置）: 培源左
16:48 功能 #2724 (已关闭): Ford_SWER_0060_0008：LIN Bus Failures- report/status frame: 诊断反馈仅对报告/状态帧有效。其余帧不反馈诊断信息。
Diagnostic purposes is only valid for report/status frame. 槐杨
16:47 功能 #2723 (已关闭): Ford_SWER_0086_0007: CANOE read of MEC: "EDF2"中可读取MEC值,可通过$22服务读EDF2,具体请见"Ford LDM4 Diagnostic Parameter Tables"表格
上位机通过读EDF2获取MEC状态,不需转义,只需直接读取LDM中存储的MEC值盛炜朱
16:42 功能 #2639 (已解决): Ford_SWER_0011_0007：Turn Indicator Failsafe Mode（TI Feedback）: 培源左
16:41 功能 #2638 (已关闭): Ford_SWER_0011_0006：Turn Indicator Failsafe Mode（Active Load Fault Reporting via LIN）: 培源左
16:41 功能 #2722 (已关闭): Ford_SWER_0086_0006: read of MEC: "EDF2"中可读取MEC值,可通过$22服务读EDF2,具体请见"Ford LDM4 Diagnostic Parameter Tables"表格盛炜朱
16:40 功能 #2721 (已关闭): Ford_SWER_0060_0007：LIN Bus Failures- Other wires: 除电源、接地或串行数据外，ECU的任何单线电路短路或断路不应妨碍与该ECU进行诊断通信的能力。
A short or open in any single wiring circuit of an ECU, except for... 槐杨
16:39 功能 #2720 (已关闭): Ford_SWER_0086_0005: CANOE write MEC: 写入MEC值需要先通过$27服务解锁,然后通过$2E服务写入,具体请见"Ford LDM4 Diagnostic Parameter Tables"表格
上位机中该功能还需要权限管理,不能拿到上位机就可以写MEC. 盛炜朱
16:39 功能 #2637 (已解决): Ford_SWER_0011_0005：Turn Indicator Failsafe Mode（N-1 Failure Detection）: 培源左
16:38 功能 #2719 (已关闭): Ford_SWER_0086_0004: write MEC: 写入MEC值需要先通过$27服务解锁,然后通过$2E服务写入,具体请见"Ford LDM4 Diagnostic Parameter Tables"表格盛炜朱
16:37 功能 #2718 (已关闭): Ford_SWER_0060_0006：LIN Bus Failures- Bus Wiring Short to Battery Rcv: 当总线短接电源故障排除后，在功能延迟章节确定的时间内，无需操作员干预即可恢复正常操作。
Upon removal of the fault, normal operation shall resume without any ... 槐杨
16:35 功能 #2717 (已关闭): Ford_SWER_0060_0005：LIN Bus Failures- Bus Wiring Short to Battery: 当母线短接正极电池小于26.5 V （Vbatt < 26.5 V）时，网络数据通信可能中断，但不会损坏任何设备。母线与电池之间的网络阻抗小于50 Ω应视为短接，不保证或不要求继续通信。
Network data communi... 槐杨
16:34 功能 #2636 (已解决): Ford_SWER_0011_0004：Turn Indicator Failsafe Mode（Channel Open/Short Detection）: 培源左
16:33 功能 #2635 (已解决): Ford_SWER_0011_0003：Turn Indicator Failsafe Mode（TI Bin Sense）: 培源左
16:31 功能 #2716 (已关闭): Ford_SWER_0060_0004：LIN Bus Failures- Bus Wiring Short to Ground Rcv: LIN短路至地故障排除后，在功能延迟章节REQ0040(#2560), 确定的时间内，无需操作员干预即可恢复正常操作。
Upon removal of the fault, normal operation shall resu... 槐杨
16:30 功能 #2634 (已解决): Ford_SWER_0011_0002：Turn Indicator Failsafe Mode（TI Thermal Derating）: 培源左
16:30 功能 #2715 (已关闭): Ford_SWER_0060_0003：LIN Bus Failures- Bus Wiring Short to Ground: 母线和地之间的网络阻抗小于50 Ω应被认为是短地，不保证或不需要继续通信。网络数据通信可能中断，但当总线接地短路时，不会损坏任何ECU。
Network data communications may be interrupte... 槐杨
16:29 功能 #2633 (已解决): Ford_SWER_0011_0001：Turn Indicator Failsafe Mode（TI Light Output）: 培源左
16:28 功能 #2714 (已关闭): Ford_SWER_0060_0002：LIN Bus Failures-LDM Power Loss Rcv: 恢复正常电源后，在功能延迟章节REQ0040（#ID2560），规定的时间内，无需操作人员干预即可恢复正常操作。
Upon return to normal power, normal operation shall resum... 槐杨
16:25 功能 #2713 (已关闭): Ford_SWER_0060_0001：LIN Bus Failures-LDM Power Loss: LDM功率损耗- LDM在功率损耗（或低电压）情况下不会干扰其余总线ecu （LDM， HCM）之间的正常通信。
LDM Power Loss – LDM shall not interfere with normal comm... 槐杨
16:20 功能 #2629 (进行中): Ford_SWER_0010_0009：Channel 1 Failsafe Mode(Channels 2-4 Assigned to LB): 培源左
16:18 功能 #2627 (进行中): Ford_SWER_0010_0008：Channel 1 Failsafe Mode(Light Connected to CH1 Low Side Driver): 培源左
16:17 功能 #2626 (进行中): Ford_SWER_0010_0007：Channel 1 Failsafe Mode(Static Bending): 培源左
16:15 功能 #2712 (已关闭): Ford_SWER_0086_0003: MEC function specification: |场景|MEC值|LDM Dataset|说明|
|产线|0xFF|EOL Dataset|模块按照EOL Dataset配置输出, APINFO4 = 1|
|下线|0x00|EOL Dataset|模块无输出(BUCK CHN... 盛炜朱
16:12 功能 #2711 (已关闭): Ford_SWER_0059_0011：LIN Lost- Front fog: 如果LIN丢失，前雾将被取消。
Front fog is to be deactivated in case of LIN lost. 槐杨
16:10 功能 #2710 (已关闭): Ford_SWER_0059_0010：LIN Lost- Lit star: 如果LIN丢失，Lit star灯将被停用。
Lit star is to be deactivated in case of LIN lost. 槐杨
16:08 功能 #2709 (已关闭): Ford_SWER_0059_0009：LIN Lost- Side Marker: 如果LIN丢失，SM灯将被激活。
Side Marker is to be activated in case of LIN lost. 槐杨
16:05 功能 #2708 (已关闭): Ford_SWER_0059_0008：LIN Lost- LIN DRL: If DRL/PL configured with LIN triggle,software should control DRL is to be activated with ‘ParkPos_Intensity_cfg’ in ... 槐杨
16:04 功能 #2707 (已关闭): Ford_SWER_0059_0007：LIN Lost- TI/LB/DRL Hardwared: TI/LB/DRL Hardwared 激活不依赖于LIN信号，也没有任何LIN丢失的故障模式
TI/LB/Hardwired DRL activation are not dependent on LIN signals an... 槐杨
16:01 功能 #2706 (已关闭): Ford_SWER_0059_0006：LIN Lost- HB Off: Software should turn off HB,when LIN lost occured. 槐杨
15:58 功能 #2705 (已关闭): Ford_SWER_0086_0002: MEC data requirement: 1. 软件在NVM中存在生产模式标志位-"MEC";
2. MEC标志位被清除后，上位机发送退出MEC指令，模块在1s之内，跳转到"下线"或者"装灯"状态盛炜朱
15:56 功能 #2703 (已关闭): Ford_SWER_0086_0001: output status when MEC = 0: 由于EOL模式需要测试LDM的极限输出能力所有通道均使能输出, 故出厂后需要关闭所有输出(BUCK CHN/PWM CHN/LSSS CHN)以防止LDM装灯后写入整灯项目配置前烧坏负载. 盛炜朱
15:53 功能 #2702 (已关闭): Ford_SWER_0059_0004：LIN Lost- last valid frames: 如果收到损坏的帧，软件将按最后接收到的有效帧执行，维持最后一帧状态输出.
If corrupt frames are received, the last valid frames shall be used in the ... 槐杨
15:47 功能 #2701 (已关闭): Ford_SWER_0059_0003：LIN Lost- Recover: 如果LDM在500ms内接收到3个有效的LIN信号，LDM将恢复正常工作。
The LDM shall go back to normal function if the LDM receives 3 valid LIN s... 槐杨
15:45 功能 #2700 (已关闭): Ford_SWER_0059_0002：LIN Lost- Above and equal Voltage: 模块main power电压大于等于7V时，2000ms （+/- 50mS）无LIN消息或损坏LIN消息，会出现“LIN丢失”的情况：
A “LIN lost” situation occurs if:
2000... 槐杨
15:44 功能 #2699 (已关闭): Ford_SWER_0059_0001：LIN Lost-Under Voltage: 当模块main power电压低于7V时，5000ms （+/- 50mS）没有收到LIN消息或损坏的LIN消息，会出现“LIN丢失”的情况：
A “LIN lost” situation occurs if:
5... 槐杨
15:44 功能 #2624 (进行中): Ford_SWER_0010_0006：Channel 1 Failsafe Mode(Active Load Fault Reporting via LIN): 培源左
15:43 功能 #2623 (进行中): Ford_SWER_0010_0005：Channel 1 Failsafe Mode(N-1 Failure Detection): 培源左
15:40 功能 #2621 (已解决): Ford_SWER_0010_0004：Channel 1 Failsafe Mode(Channel Open/Short Detection): 培源左
15:39 功能 #2620 (已解决): Ford_SWER_0010_0003：Channel 1 Failsafe Mode(LB Bin Sense): 培源左
15:38 功能 #2698 (已关闭): Ford_SWER_0058_0003：NTC Thermistor Failure-FAN: 如果NTC电阻丢失或者超出范围，且功能/FAN绑定该NTC的时候，分配的FAN需运行
(Even if there is a Fan attached, the LDM shall run the Fan.) 槐杨
15:37 功能 #2619 (已解决): Ford_SWER_0010_0002：Channel 1 Failsafe Mode(LB Thermal Derating): 培源左
15:35 功能 #2697 (已关闭): Ford_SWER_0058_0002：NTC Thermistor Failure-out is of range: 如果NTC电阻超出范围：
1. 如果配置了NTC降额，LED按照最低降额点输出；
2. 如果没有配置NTC降额，led 应由RBIN电阻定义的电流驱动
(If the NTC resistor is lost or its va... 槐杨
15:33 功能 #2696 (已关闭): Ford_SWER_0001_0002：因CH2不可用进入Failsafe工况后，其他通道也可以作为相对应灯光的功率输入线: 需求：but the LDM shall be also capable of switching to the failsafe power supply when the main power supply is not avai... 云浩汪
15:32 功能 #2695 (已关闭): Ford_SWER_0010_0010：Channel 1 Failsafe Mode(BCM failsafe mode): 软件中需要周期性识别主电源（Input Channel2）是否存在，若丢失主电源(Input channel 2 = LOW)，且此时Input Channel1和Input Channel3任一个存在，或同时存在，则进入BCM fa... 培源左
15:31 功能 #2694 (已关闭): Ford_SWER_0058_0001：NTC Thermistor Failure-lost: 如果NTC电阻丢失：
1. 如果配置了NTC降额，LED按照最低降额点输出；
2. 如果没有配置NTC降额，led 应由RBIN电阻定义的电流驱动
(If the NTC resistor is lost or its valu... 槐杨
15:25 功能 #2693 (已关闭): Ford_SWER_0057_0002：Binning Resistor Lost or Out of Range - Out of Range: 如果RBIN电阻超出范围，不应导致通道过流超过BCM电流限制，LDM使用模块存储的历史档位，实现电流输出
(If the binning resistor is lost (short circuit or open circu... 槐杨
15:24 功能 #2692 (已关闭): Ford_SWER_0057_0001：Binning Resistor Lost or Out of Range - Lost: 如果RBIN电阻丢失（未识别到有效档位），不应导致通道过流超过BCM电流限制，LDM使用模块存储的历史档位，实现电流输出
(If the binning resistor is lost (short circuit or op... 槐杨
15:19 功能 #2691 (已关闭): Ford_SWER_0056_0003： Buck Failure Detection - Open circuits: buck自身检测到的失败如下：
开路
（The failures that the buck itself detects are the followings:
Open circuits
）
!c... 槐杨
15:19 功能 #2690 (已关闭): Ford_SWER_0056_0002： Buck Failure Detection - Short to battery in HSD when it is off: buck自身检测到的失败如下：
HSD关闭时，HSD短路到电源
（The failures that the buck itself detects are the followings:
o Short... 槐杨
15:17 Bug #2689 (Bug-已关闭): boost问题: 在dataset上设置BOOST电压为0v，这个时候boost电压测量还有5v的电压（C63）传鹏胡
15:14 功能 #2688 (已关闭): Ford_SWER_0056_0001： Buck Failure Detection-Short to GND: buck自身检测到的失败如下：
短接GND
（The failures that the buck itself detects are the followings:
Short to GND
）
!... 槐杨
15:10 功能 #2687 (已关闭): Ford_SWER_0055_0006：LDM Failure Response Reporting-TI: 如果发生LED故障（LED串开载或短路（LED≥1个短路）），LDM应在主电源在保证性能范围内（9-18V），“Ignition_status”为“Run/Start”时，TI应始终通过硬线‘ L/RF_LED_Turn_Outage... 槐杨
15:08 功能 #2686 (已关闭): Ford_SWER_0055_0005：LDM Failure Response Reporting-DRL Failure Report cfg: 如果发生LED故障（LED串开载或短路（LED≥1个短路）），LDM应在主电源在保证性能范围内（9-18V），“Ignition_status”为“Run/Start”时，通过配置实现是否通过LIN总线报告故障。
（In cas... 槐杨
15:07 功能 #2617 (已解决): Ford_SWER_0010_0001：Channel 1 Failsafe Mode(LB Light Output): 培源左
15:06 功能 #2685 (已关闭): Ford_SWER_0055_0004：LDM Failure Response Reporting-HB Failure Report cfg: 如果发生LED故障（LED串开载或短路（LED≥1个短路）），LDM应在主电源在保证性能范围内（9-18V），“Ignition_status”为“Run/Start”时，通过配置实现是否通过LIN总线报告故障。
（In cas... 槐杨
15:05 功能 #2684 (已关闭): Ford_SWER_0055_0003：LDM Failure Response Reporting-LB Failure Report cfg: 如果发生LED故障（LED串开载或短路（LED≥1个短路）），LDM应在主电源在保证性能范围内（9-18V），“Ignition_status”为“Run/Start”时，通过配置实现是否通过LIN总线报告故障。
（In cas... 槐杨
15:02 功能 #2683 (已关闭): Ford_SWER_0055_0002：LDM Failure Response Reporting-IG Status: 如果发生LED故障（LED串开载或短路（LED≥1个短路）），LDM应在主电源在保证性能范围内（9-18V），“Ignition_status”为“Run/Start”时，能够通过LIN总线报告故障。
（In case of a... 槐杨
15:02 功能 #2682 (已关闭): Ford_SWER_0001_0001：正常工况下，CH2通道为功率输入线，其他通道为逻辑输入线: 需求原文：The LDM will use Channel2 as main power input as HS REQ005, and rest channels input to be used as an input signa... 云浩汪
15:02 功能 #2681 (已关闭): Ford_SWER_0055_0001：LDM Failure Response Reporting-Voltage range: （In case of a LED failure (LED string open load or short circuit (LEDs ≥1 short circuit（parameter xx_Failure_Deact_cf... 槐杨
14:50 功能 #2680 (已关闭): Ford_SWER_0054_0008：Load Failure Response Deactivation-Over Voltage range: 输入电压超出9-16V范围后，不反馈其余故障，仅反馈输入故障
(When the input voltage exceeds the range of 9-16V, no fault is reported, only unde... 槐杨
14:46 功能 #2679 (已关闭): Ford_SWER_0054_0007：Load Failure Response Deactivation-N-1 Failure: 注：当N-1 LED单光功能失效时，其他功能继续工作。
示例：当LSD的led失效时，下一个更高的子系统（例如，High Side Driver）仍将根据上述参数工作。
NOTE: In case of N-1 LED fai... 槐杨
14:46 功能 #2677 (已解决): Ford_SWER_0009_0001：Channel 1 output Assignment(Dataset Channel 1 combine LB): 已完成培源左
14:41 功能 #2677 (已关闭): Ford_SWER_0009_0001：Channel 1 output Assignment(Dataset Channel 1 combine LB): Dataset中Output Channel1功能配置固定为LB不可修改。
(The configuration of the Output Channel1 function in Dataset is fixed to LB a... 培源左
14:45 功能 #2678 (已关闭): Ford_SWER_0009_0002：Channel 1 output Assignment(APP Channel 1 combine LB): 软件中Output Channel1默认绑定LB功能输出，不能通过配置改变。
(Output Channel1 in the software is bound to the LB output by default and can... 培源左
14:37 功能 #2676 (已关闭): Ford_SWER_0054_0006：Load Failure Response Deactivation-TI Cfg: 如果发生故障（1个或多个LED开载或短路），受影响组件的下一个更高的子系统（整个LED串）是否停用，可以通过参数进行配置。
‘ TI_ Failure_Deact_cfg ’参数定义：
•0x00：不需要去激活
•0x01：在检... 槐杨
14:32 功能 #2675 (已关闭): Ford_SWER_0053_0005：General LED Failure Detection_Power up: 在LDM通电500毫秒内，不能通过LIN报告故障。在每次“LDM电源循环”期间，故障检测将重新开始。
该模块必须能够检测与LED相关的以下故障：
• 单个或多个LED故障（每个通道）
• 阳极到阴极短路
• 阳极到阴极... 槐杨
14:29 功能 #2660: Ford_SWER_0053_0003：General LED Failure Detection_LIN feedback: 在1s内反馈故障槐杨
11:11 功能 #2660 (已关闭): Ford_SWER_0053_0003：General LED Failure Detection_LIN feedback: 每次故障都需要通过LIN进行通信。在报告故障之前，需要至少在1秒内对故障进行10次验证。
该模块必须能够检测与LED相关的以下故障：
• 单个或多个LED故障（每个通道）
• 阳极到阴极短路
• 阳极到阴极断路
• BIN/... 槐杨
14:29 功能 #2674 (已关闭): Ford_SWER_0053_0002：General LED Failure Detection_IG status: 在每个“LDM电源周期”中（模块重新上电），重新启动停机检测。
（On every ‘LDM power cycle’ the outage detection is restarted.）槐杨
14:21 功能 #2659: Ford_SWER_0053_0001：General LED Failure Detection_Voltage range: 故障检测仅在通道处于开启状态且输入电压在保证性能范围内（9-16V）时发生。超出范围时不报故障。
该模块必须能够检测与LED相关的以下故障：
• 单个或多个LED故障（每个通道）
• 阳极到阴极短路
• 阳极到... 槐杨
11:09 功能 #2659 (已关闭): Ford_SWER_0053_0001：General LED Failure Detection_Voltage range: 故障检测仅在通道处于开启状态且输入电压(Main Power)在保证性能范围内（9-16V）时发生。
该模块必须能够检测与LED相关的以下故障：
• 单个或多个LED故障（每个通道）
• 阳极到阴极短路
• 阳极到阴极断路
... 槐杨
14:10 功能 #2673 (已关闭): Ford_SWER_0054_0005：Load Failure Response Deactivation-DRL Cfg: 如果发生故障（1个或多个LED开载或短路），受影响组件的下一个更高的子系统（整个LED串）是否停用，可以通过参数进行配置。
‘ DRL_ Failure_Deact_cfg ’参数定义：
•0x00：不需要去激活
•0x01：在... 槐杨
14:10 功能 #2530 (进行中): Ford_SYSR：FS_REQ0010_V1 Channel 1 Failsafe Mode: 斌徐
13:52 功能 #2672 (已关闭): Ford_SWER_0054_0004：Load Failure Response Deactivation-HB Cfg: 如果发生故障（1个或多个LED开载或短路），受影响组件的下一个更高的子系统（整个LED串）是否停用，可以通过参数进行配置。
‘ HB_ Failure_Deact_cfg ’参数定义：
•0x00：不需要去激活
•0x01：在检... 槐杨
13:49 功能 #2671 (已关闭): Ford_SWER_0054_0003：Load Failure Response Deactivation-LB Cfg: 如果发生故障（1个或多个LED开载或短路），受影响组件的下一个更高的子系统（整个LED串）是否停用，可以通过参数进行配置。
‘ LB_Failure_Deact_cfg ’参数定义：
•0x00：不需要去激活
•0x01：在... 槐杨
13:45 功能 #2670 (已关闭): Ford_SWER_0015_0011：Low Side Driver 1 and 2 usage Configuration(LSD Duty Cycle): APP读取Dataset的生成数据，相应LSD通道按照“LSD1/2_ Duty_Cycle_cfg”数据输出占空比。
(The APP reads the generated data of the Dataset, and th... 培源左
13:06 功能 #2669 (已关闭): Ford_SWER_0015_0010：Low Side Driver 1 and 2 usage Configuration(HB/FTP Base IGN): APP读取Dataset数据，若存在“LSD1/2_usage_cfg”为0x02，则收到HB/FTP命令时，若IGN处于运行或启动状态时，才能激活相应的通道输出。
(When the APP reads Dataset data,... 培源左
12:53 功能 #2668 (已关闭): Ford_SWER_0015_0009：Low Side Driver 1 and 2 usage Configuration(DRL2 clash): DRL2只能分配给一个LSD通道。
(DRL2 can only be assigned to one LSD channel.) 培源左
12:51 功能 #2667 (已关闭): Ford_SWER_0054_0002：Load Failure Response Deactivation-Temperature Range: LED断电检测应在-40℃至110℃环境温度范围内工作。
（LED outage detection shall work within -40 to 110°C ambient temperature range）槐杨
12:50 功能 #2666 (已关闭): Ford_SWER_0015_0008：Low Side Driver 1 and 2 usage Configuration(SBL): APP读取Dataset的生成数据，若“LSD1/2_usage_cfg”为0x04，则对应LSD关联SBL功能。
当收到SBL信号时，对应LSD应当被激活，并按照设定方式输出。
(The APP reads the genera... 培源左
12:50 功能 #2665 (已关闭): Ford_SWER_0054_0001：Load Failure Response Deactivation-Voltage range: LED断电检测输入电压范围为9-16V。如果输入电压超出范围，则不报告LED断电。
（ Input voltage range for LED outage detection is 9-16V. No LED outages... 槐杨
12:48 功能 #2664 (已关闭): Ford_SWER_0015_0007：Low Side Driver 1 and 2 usage Configuration(DRL2): APP读取Dataset的生成数据，若“LSD1/2_usage_cfg”为0x03，则对应LSD关联DRL2功能。
当收到DRL信号时，对应LSD应当被激活，并输出对应“LSDx_ Duty_Cycle_cfg”占空比；
当收到... 培源左
12:46 功能 #2663 (已关闭): Ford_SWER_0015_0006：Low Side Driver 1 and 2 usage Configuration(HB): APP读取Dataset的生成数据，若“LSD1/2_usage_cfg”为0x02，则对应LSD关联HB功能。
当收到HB信号时，对应LSD应当被激活，并按照设定方式输出。
(The APP reads the generate... 培源左
12:44 功能 #2662 (已关闭): Ford_SWER_0015_0005：Low Side Driver 1 and 2 usage Configuration(LB): APP读取Dataset的生成数据，若“LSD1/2_usage_cfg”为0x01，则对应LSD关联LB功能。
当收到LB信号时，对应LSD应当被激活，并按照设定方式输出。
(The APP reads the generate... 培源左
12:40 功能 #2661 (已关闭): Ford_SWER_0015_0004：Low Side Driver 1 and 2 usage Configuration(Not used): APP读取Dataset的生成数据，若“LSD1/2_usage_cfg”为0x00，则对应LSD未关联功能
(The APP reads the generated data of the Dataset. If LSD1/2_u... 培源左
11:07 功能 #2658 (已关闭): Ford_SWER_0015_0003：Low Side Driver 1 and 2 usage Configuration(Dataset LSD cycle): Dataset 可以通过“LSD1/2_ Duty_Cycle_Cfg”配置LSD1/2占空比。
(Dataset Can set the LSD1/2 duty ratio using LSD1/2_Duty_Cycle_Cfg.... 培源左
11:03 功能 #2657 (已关闭): Ford_SWER_0053_0004：General LED Failure Detection_All Chn: 该LDM必须支持对所有输出通道的故障检测,该模块必须能够检测与LED相关的以下故障：
• 单个或多个LED故障（每个通道）
• 阳极到阴极短路
• 阳极到阴极断路
• BIN/NTC超出范围
(The LDM must ... 槐杨
10:55 功能 #2656 (已关闭): Ford_SWER_0015_0002：Low Side Driver 1 and 2 usage Configuration(Dataset DRL2 clash): Dataset 中“LSD1/2_usage_cfg”应该只有一个LSD可以配置为“DRL2”，若两项都配置为“DRL2”时，操作将被撤回，并报错。
(Only one LSD in the Dataset LSD1/2_usage... 培源左

2024-10-27

17:04 功能 #2655 (已关闭): Ford_SWER_0015_0001：Low Side Driver 1 and 2 usage Configuration(Dataset_Lsd_usage): Dataset应该可以通过“LSD1/2_usage_cfg”，配置LSD的功能，并生成对应的数据。
(Dataset should be able to configure LSD functions and generate d... 培源左
15:55 功能 #2654 (已关闭): Ford_SWER_0014_0006：Low Side Driver 1 and 2 Channel Configuration(LSD assignment Channel4): APP读取Dataset的生成数据，若“LSD1/2_channel_assignment_cfg”为0x04，
则对应LSD连接Channel4输出。
(The APP reads the generated data from... 培源左
15:54 功能 #2653 (已关闭): Ford_SWER_0014_0005：Low Side Driver 1 and 2 Channel Configuration(LSD assignment Channel3): APP读取Dataset的生成数据，若“LSD1/2_channel_assignment_cfg”为0x03，
则对应LSD连接Channel3输出。
(The APP reads the generated data from... 培源左
15:53 功能 #2652 (已关闭): Ford_SWER_0014_0004：Low Side Driver 1 and 2 Channel Configuration(LSD assignment Channel2): APP读取Dataset的生成数据，若“LSD1/2_channel_assignment_cfg”为0x02，
则对应LSD连接Channel2输出。
(The APP reads the generated data from... 培源左
15:44 功能 #2648 (已关闭): Ford_SWER_0014_0003：Low Side Driver 1 and 2 Channel Configuration(LSD assignment Channel1): APP读取Dataset的生成数据，若“LSD1/2_channel_assignment_cfg”为0x01，
则对应LSD连接Channel1输出。
(The APP reads the generated data from... 培源左
15:41 功能 #2647 (已关闭): Ford_SWER_0014_0002：Low Side Driver 1 and 2 Channel Configuration(LSD Not used): APP读取Dataset的生成数据，若“LSD1/2_channel_assignment_cfg”为0x00，
则对应LSD不启用，不会联动任何通道输出。
(The APP reads the generated data fr... 培源左
15:34 功能 #2646 (已关闭): Ford_SWER_0014_0001：Low Side Driver 1 and 2 Channel Configuration(Dataset Cfg): Dataset需要通过“LSD1/2_channel_assignment_cfg”配置项，来配置LSD连接到哪个通道或者不启用，并生成以下对应数据。
(The Dataset uses the LSD1/2_channel_ass... 培源左

2024-10-25

16:37 功能 #2645 (已关闭): Ford_SWER_0013_0006：Channel 2 to 4 Functional Configuration（TI）: APP读取Dataset的生成数据，若“Channel2/3/4_usage_cfg”为0x04，
则对应通道只应响应Turn Indicator信号输出。
(The APP reads the generated data fr... 培源左
16:36 功能 #2644 (已关闭): Ford_SWER_0013_0005：Channel 2 to 4 Functional Configuration（DRL）: APP读取Dataset的生成数据，若“Channel2/3/4_usage_cfg”为0x03，
则对应通道只应响应DRL信号输出。
(The APP reads the generated data from the Data... 培源左
16:35 功能 #2643 (已关闭): Ford_SWER_0013_0004：Channel 2 to 4 Functional Configuration（HB）: APP读取Dataset的生成数据，若“Channel2/3/4_usage_cfg”为0x02，
则对应通道只应响应HB信号输出。
(The APP reads the generated data from the Datas... 培源左
16:34 功能 #2642 (已关闭): Ford_SWER_0013_0003：Channel 2 to 4 Functional Configuration（LB）: APP读取Dataset的生成数据，若“Channel2/3/4_usage_cfg”为0x01，
则对应通道只应响应LB信号输出。
(The APP reads the generated data from the Datas... 培源左
16:32 功能 #2641 (已关闭): Ford_SWER_0013_0002：Channel 2 to 4 Functional Configuration（Not used）: APP读取Dataset的生成数据，若“Channel2/3/4_usage_cfg”为0x00，
则对应通道不被启动，任何情况都不应该输出。
(The APP reads the generated data from the ... 培源左
16:26 功能 #2640 (已关闭): Ford_SWER_0013_0001：Channel 2 to 4 Functional Configuration（Dataset配置）: Dataset中应该支持将“Channel2/3/4_usage_cfg”参数，配置为以下功能，并生成对应的数据。
(The Dataset should support setting the Channel2/3/4_usage... 培源左
16:08 功能 #2639 (已关闭): Ford_SWER_0011_0007：Turn Indicator Failsafe Mode（TI Feedback）: 软件进入到Failsafe Mode，且识别到有“TI Power supply Channel”(L/RF_Turn_Lamp_Ckt)使能，同时读取到Dataset中“TI_POWER_Source_CFG”配置为0x01,“Ch... 培源左
16:06 功能 #2638 (已关闭): Ford_SWER_0011_0006：Turn Indicator Failsafe Mode（Active Load Fault Reporting via LIN）: 软件进入到Failsafe Mode，且识别到有“TI Power supply Channel”(L/RF_Turn_Lamp_Ckt)使能，同时读取到Dataset中“TI_POWER_Source_CFG”配置为0x01,“Ch... 培源左
15:44 功能 #2637 (已关闭): Ford_SWER_0011_0005：Turn Indicator Failsafe Mode（N-1 Failure Detection）: 软件进入到Failsafe Mode，且识别到有“TI Power supply Channel”(L/RF_Turn_Lamp_Ckt)使能，同时读取到Dataset中“TI_POWER_Source_CFG”配置为0x01,“Ch... 培源左
15:41 功能 #2636 (已关闭): Ford_SWER_0011_0004：Turn Indicator Failsafe Mode（Channel Open/Short Detection）: 软件进入到Failsafe Mode，且识别到有“TI Power supply Channel”(L/RF_Turn_Lamp_Ckt)使能，同时读取到Dataset中“TI_POWER_Source_CFG”配置为0x01,“Ch... 培源左
15:37 功能 #2635 (已关闭): Ford_SWER_0011_0003：Turn Indicator Failsafe Mode（TI Bin Sense）: 软件进入到Failsafe Mode，且识别到有“TI Power supply Channel”(L/RF_Turn_Lamp_Ckt)使能，同时读取到Dataset中“TI_POWER_Source_CFG”配置为0x01,“Ch... 培源左
15:35 功能 #2634 (已关闭): Ford_SWER_0011_0002：Turn Indicator Failsafe Mode（TI Thermal Derating）: 软件进入到Failsafe Mode，且识别到有“TI Power supply Channel”(L/RF_Turn_Lamp_Ckt)使能，同时读取到Dataset中“TI_POWER_Source_CFG”配置为0x01,“Ch... 培源左
15:16 功能 #2633 (已关闭): Ford_SWER_0011_0001：Turn Indicator Failsafe Mode（TI Light Output）: 软件进入到Failsafe Mode，且识别到有“TI Power supply Channel”(L/RF_Turn_Lamp_Ckt)使能，同时读取到Dataset中“TI_POWER_Source_CFG”配置为0x01,“Ch... 培源左
15:13 功能 #2632 (已关闭): Ford_SWER_0007_0002: 转向灯触发信号规格: 转向灯触发信号是1.33Hz, 50%占空比;(375ms) 盛炜朱
15:12 功能 #2631 (已关闭): Ford_SWER_0007_0001: 转向灯触发方式: Dataset中TI功能触发通道可以配置为“Power Supply Channel 3”或无效，并生成对应的数据。
(The TI function trigger Channel in the Dataset can be co... 盛炜朱
15:10 功能 #2625: Ford_SWER_0051_0001：NTC temperature to resistance: add R,R0,B,T0 and T description
R = NTC Resistance at T (Ω)
R0 = Resistance at T0 (Ω)
B = NTC B – Constant value (... 涛陆
14:53 功能 #2625 (已关闭): Ford_SWER_0051_0001：NTC temperature to resistance: The software shall calculate NTC resistors value by configuring the R0 and B-constant of the thermistor within the LD... 涛陆
15:10 功能 #2630 (已关闭): Ford_SWER_0006_0001: DRL/PO触发方式: "DRL/PO"有两种控制来源:
1. "BCM"硬线发送"PWM控制信号"
2. "BCM" "LIN命令"DRL_Rqst"
Dataset中可配置DRL/PO的控制方式盛炜朱
15:07 功能 #2629 (已关闭): Ford_SWER_0010_0009：Channel 1 Failsafe Mode(Channels 2-4 Assigned to LB): 软件识别到Input Channel1（L/RF_Low_Beam_Ckt）使能且main power失效（Input Channel 2失效）时，
如果Output Channel2、3、4被配置成LB功能，该部分输出通道禁止输出... 培源左
15:06 功能 #2628 (已关闭): Ford_SWER_0005_0001：输入通道2供电模式: 输入通道2是主供电, 能够通过AD端口，识别电压范围。
当Input CHN2丢失,但LDM通过Input CHN1/CHN3/CHN4获电,则LDM需要通过LIN通讯对外报如下故障:
!clipboard-202411011... 盛炜朱
15:04 功能 #2627 (已关闭): Ford_SWER_0010_0008：Channel 1 Failsafe Mode(Light Connected to CH1 Low Side Driver): 软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
连接到Output Channel1的低边部分灯不可被点亮。
(When the software ent... 培源左
14:59 功能 #2626 (已关闭): Ford_SWER_0010_0007：Channel 1 Failsafe Mode(Static Bending): 软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
Static Bending不可被点亮。
(When the software enters Failsa... 培源左
14:52 功能 #2624 (已关闭): Ford_SWER_0010_0006：Channel 1 Failsafe Mode(Active Load Fault Reporting via LIN): 软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
若读取到Dataset生成的数据配置有LB故障上报功能，Output Channel1的LB需要能满足Act... 培源左
14:50 功能 #2623 (已关闭): Ford_SWER_0010_0005：Channel 1 Failsafe Mode(N-1 Failure Detection): 软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
若读取到Dataset生成的数据中“LB_Failure_Deact_cfg”配置为0x01/0x02时，O... 培源左
14:44 功能 #2522: Ford_SYSR：FS_REQ0002_V1 LDM Input Transients: 非软件需求, 需测试注意盛炜朱
11:52 功能 #2522 (进行中): Ford_SYSR：FS_REQ0002_V1 LDM Input Transients: 玉洁金
09:24 功能 #2522: Ford_SYSR：FS_REQ0002_V1 LDM Input Transients: 完成涛陆
14:44 功能 #2524: Ford_SYSR：FS_REQ0004_V1 Channel 1 Power Mode: 非软件需求, 测试需注意盛炜朱
09:25 功能 #2524: Ford_SYSR：FS_REQ0004_V1 Channel 1 Power Mode: 完成涛陆
14:39 功能 #2622 (已关闭): Ford_SWER_0052_0001：LED Thermal Derating Smooth Appearance: APP:The LDM shall thermal dim at a rate no greater than 2.5%/sec.
now： rate = 2% 涛陆
14:37 功能 #2621 (已关闭): Ford_SWER_0010_0004：Channel 1 Failsafe Mode(Channel Open/Short Detection): 软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
Output Channel1的LB需要能满足Channel Open/Short Detection功能。... 培源左
14:34 功能 #2620 (已关闭): Ford_SWER_0010_0003：Channel 1 Failsafe Mode(LB Bin Sense): 软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
Output Channel1的LB需要能满足LB Bin Sense功能。
(When the soft... 培源左
14:31 功能 #2619 (已关闭): Ford_SWER_0010_0002：Channel 1 Failsafe Mode(LB Thermal Derating): 软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
Output Channel1的LB需要能满足LB Thermal Derating功能。
(When t... 培源左
14:27 功能 #2618 (已关闭): Ford_SWER_0001_0005：电源电压采样过滤时间: 电源电压采样及过滤时间需要大于 -500- 250ms以避免如EMC实验波形注入导致LED亮度变化. 盛炜朱
14:24 功能 #2617 (已关闭): Ford_SWER_0010_0001：Channel 1 Failsafe Mode(LB Light Output): 软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
Output Channel1的LB需要正常点亮。
(When the software enters F... 培源左
14:23 功能 #2616 (已关闭): Ford_SWER_0001_0004：电源电压降功率平滑过渡: 电源电压降功率需要采用平滑过渡算法防止亮度突然跳变盛炜朱
14:19 功能 #2615 (已关闭): Ford_SWER_0001_0003：电源电压降功率波形: 电压缓升和缓降，对于所有功能点亮（前提即main power和LB/TI power电压一致, LIN点灯信号ok），电压缓升时到达7V时HB+DRL/POS以20%（假设最低可承受输出）输出，并保持到8V，LB+TI开始以20%点亮... 盛炜朱
14:01 功能 #2614 (已关闭): Ford_SWER_0003_0004：Dataset中对于DRL/PO功能的配置: !clipboard-202410291648-bqeje.png!
Dataset中需要能对DRL/PO功能的触发源进行设定
INVALID - 本项目没有DRL/PO功能
InputCHN4 - 通过LDM Input ch... 盛炜朱
13:40 功能 #2612 (已关闭): Ford_SWER_0003_0003：输入通道3的功能: Dataset中可以将Input Channel3作为TI的输入配置;
APP需要获取Dataset中Input Channel3的配置,当配置为TI功能时,软件需要获取Input Channel3高低电平;当配置为Invalid功... 盛炜朱
13:25 功能 #2611 (已关闭): Ford_SWER_0003_0002：输入通道2的功能: App需要识别Input Channel2作为主电源是否存在的判断;
Dataset中无需对于Input Channel2做配置项;
上位机需要能读出Input Channel2的电压; 盛炜朱
13:20 功能 #2610 (已关闭): Ford_SWER_0003_0001：输入通道1的功能: LB功能只绑定在Input channel1上
APP只需要获取Input channel1的高地电平状态经过滤波后即可以判定LB On或者Off;
Dataset无需该条配置项; 盛炜朱
13:10 功能 #2523: Ford_SYSR：FS_REQ0003_V2 Channel power source Configuration: 客户已经更新该条需求,最新需求需结合LDM Localization Dataset_V1.6:
Input Channel 3只能配置为:Invalid或者TI无法配置为DRL
Input Channel 4只能配置为:Inva... 盛炜朱
11:54 功能 #2523 (进行中): Ford_SYSR：FS_REQ0003_V2 Channel power source Configuration: 玉洁金
09:24 功能 #2523: Ford_SYSR：FS_REQ0003_V2 Channel power source Configuration: 需求有变更，按新需求完成涛陆
12:43 功能 #2567: Ford_SYSR：FS_REQ0047_V1 LED Thermal Derating: !clipboard-202410251243-cdazp.png!
客户已明确规定150mA以下才能调PWM 盛炜朱
10:59 功能 #2567: Ford_SYSR：FS_REQ0047_V1 LED Thermal Derating: !clipboard-202410251051-5zxoq.png!
客户解答LED降功率优先降电流,在保证电流精度的最小电流值后调PWM,需要结合硬件实际情况来定具体电流值. 盛炜朱
10:00 功能 #2567: Ford_SYSR：FS_REQ0047_V1 LED Thermal Derating: 完成涛陆
12:32 功能 #2520: Ford_SYSR: FS_REQ0001_V2 LDM Input: !clipboard-202410251232-5unp0.png!
盛炜朱
09:23 功能 #2520: Ford_SYSR: FS_REQ0001_V2 LDM Input: 完成涛陆
11:04 功能 #2574: Ford_SYSR：FS_REQ0054_V1 Load Failure Response Deactivation: !clipboard-202410251104-7pspv.png!
盛炜朱
10:06 功能 #2574: Ford_SYSR：FS_REQ0054_V1 Load Failure Response Deactivation: 完成涛陆
11:01 功能 #2607: Ford_SYSR：FS_REQ0086_V1 LDM Factory Mode: 有个bug需要修复涛陆
11:00 功能 #2605: Ford_SYSR：FS_REQ0084_V2 Software Flashing: 完成涛陆
10:59 功能 #2604: Ford_SYSR：FS_REQ0083_V1 MSB vs. LSB: 完成涛陆
10:57 功能 #2603: Ford_SYSR：FS_REQ0082_V1 Supplier Defined: Service Return and Development Reporting: EDF1完成，EDF2部分完成涛陆
10:57 功能 #2563: Ford_SYSR：FS_REQ0043_V2 Bin Class Current Setting: Updated REQ0043 BIN class setting
BIN current can be set for BIN0 to BIN7 of each channel in the configuration param... 玉洁金
09:57 功能 #2563: Ford_SYSR：FS_REQ0043_V2 Bin Class Current Setting: 完成涛陆
10:56 功能 #2602: Ford_SYSR：FS_REQ0081_V1 Supplier Defined: Lamp Manufacturing: 完成涛陆
10:54 功能 #2601: Ford_SYSR：FS_REQ0080_V2 LDM Self-Test Description: 未完成涛陆
10:54 功能 #2600: Ford_SYSR：FS_REQ0079_V2 Self-Test Frame: 未完成涛陆
10:52 功能 #2536: Ford_SYSR：FS_REQ0016_V3 PWM output configuration: The LDM shall have 4 PWM outputs capable of controlling any of the following functions via configure parameter ‘PWMx_... 玉洁金
09:33 功能 #2536: Ford_SYSR：FS_REQ0016_V3 PWM output configuration: 部分完成涛陆
10:50 功能 #2599: Ford_SYSR：FS_REQ0078_V1 LIN Part Number Reporting: 完成涛陆
10:49 功能 #2598: Ford_SYSR：FS_REQ0077_V3 Run Time Configuration Validation: 完成涛陆
10:46 功能 #2597: Ford_SYSR：FS_REQ0076_V1 LDM Configuration Monitoring: 完成涛陆
10:45 功能 #2596: Ford_SYSR：FS_REQ0075_V1 Configuration Support: BCM LIN功能完成涛陆
10:42 功能 #2595: Ford_SYSR：FS_REQ0074_V2 LIN Configuration Frame Definition: 完成涛陆
10:42 功能 #2594: Ford_SYSR：FS_REQ0073_V1 Node Lighting Module Configuration Mechanics: 完成涛陆
10:41 功能 #2593: Ford_SYSR：FS_REQ0072_V1 Node Lighting Module Configuration: 完成涛陆
10:38 功能 #2593: Ford_SYSR：FS_REQ0072_V1 Node Lighting Module Configuration: 完成涛陆
10:36 功能 #2592: Ford_SYSR：FS_REQ0071_V1 Description of Node Reporting: 完成涛陆
10:31 功能 #2591: Ford_SYSR：FS_REQ0070_V2 BCM EEL VO Load Sequencing: 部分完成，PWM信号未接入涛陆
10:30 功能 #2585: Ford_SYSR：FS_REQ0064_V1 EEL LIN Message Sequencing: 报文发送时序是定义在LDF里的,软件只需LIN通讯正常即可证明满足该需求. 盛炜朱
10:20 功能 #2585: Ford_SYSR：FS_REQ0064_V1 EEL LIN Message Sequencing: 与软件无关，上位机需求涛陆
10:26 功能 #2590: Ford_SYSR：FS_REQ0069_V1 BCM EEL LDM Node Status Report Frame: 大部分完成涛陆
10:24 功能 #2589: Ford_SYSR：FS_REQ0068_V1 Exterior Lighting Functional Support: 未完成，有些信号没有获取涛陆
10:22 功能 #2588: Ford_SYSR：FS_REQ0067_V1 BCM EEL Command Frame 2: 完成涛陆
10:22 功能 #2587: Ford_SYSR：FS_REQ0066_V1 BCM EEL Command Frame 1: 完成涛陆
10:21 功能 #2586: Ford_SYSR：FS_REQ0065_V1 EEL LIN Identifier Allocation: 完成涛陆
10:19 功能 #2584: Ford_SYSR：FS_REQ0063_V2 LDF: 完成涛陆
10:18 功能 #2583: Ford_SYSR：FS_REQ0062_V2 LDM diagnostic with test command: 未完成涛陆
10:14 功能 #2582: Ford_SYSR：FS_REQ0061_V3 Failure Recover strategy: LDM receives 3 valid LIN signals within 500 ms未完成涛陆
10:12 功能 #2581: Ford_SYSR：FS_REQ006x_V2 LB Activation Redundant: 未完成涛陆
10:10 功能 #2580: Ford_SYSR：FS_REQ0060_V1 LIN Bus Failures: 未完成涛陆
10:10 功能 #2579: Ford_SYSR：FS_REQ0059_V1 LIN Lost: 未完成涛陆
10:08 功能 #2578: Ford_SYSR：FS_REQ0058_V1 NTC Thermistor Failure: 完成涛陆
10:08 功能 #2577: Ford_SYSR：FS_REQ0057_V1 Binning Resistor Lost or Out of Range: 完成涛陆
10:07 功能 #2576: Ford_SYSR：FS_REQ0056_V1 Buck Failure Detection: 完成涛陆
10:07 功能 #2575: Ford_SYSR：FS_REQ0055_V3 LDM Failure Response Reporting: 完成涛陆
10:06 功能 #2573: Ford_SYSR：FS_REQ0053_V2 General LED Failure Detection: 完成涛陆
10:05 功能 #2572: Ford_SYSR：FS_REQ0052_V1_LED Thermal Derating Smooth Appearance: 曲线有问题，需要修改涛陆
10:04 功能 #2571: Ford_SYSR：FS_REQ0051_V1 NTC Calculation: 完成涛陆
10:04 功能 #2570: Ford_SYSR：FS_REQ0050_V2 LDM intermal Thermal Derating: 涛陆在 #note-1 中写到：
> 按照DV mode给的曲线开发的，未按照FS开发
SBL部分未开发涛陆
10:02 功能 #2570: Ford_SYSR：FS_REQ0050_V2 LDM intermal Thermal Derating: 按照DV mode给的曲线开发的，未按照FS开发涛陆
10:01 功能 #2569: Ford_SYSR：FS_REQ0049_V2 Output Thermal Derating curve: 完成涛陆
10:00 功能 #2568: Ford_SYSR：FS_REQ0048_V1 Thermal Monitoring: 完成涛陆
09:59 功能 #2566: Ford_SYSR：FS_REQ0046_V1 Fan Failure Detection: 部分完成涛陆
09:58 功能 #2565: Ford_SYSR：FS_REQ0045_V2 Activation of the Fan: 完成涛陆
09:58 功能 #2564: Ford_SYSR：FS_REQ0044_V1 FAN Functional self-test when power on: 未完成涛陆
09:57 功能 #2562: Ford_SYSR：FS_REQ0042_V2 Binning Resistor: 完成涛陆
09:56 功能 #2561: Ford_SYSR：FS_REQ0041_V2 Channel output intensity Smooth Fading: 完成涛陆
09:55 功能 #2560: Ford_SYSR：FS_REQ0040_V1 Light Source Activation Latency Times: 热启动有问题涛陆
09:55 功能 #2559: Ford_SYSR：FS_REQ0039_V2 Fading Requirements: 未完成涛陆
09:53 功能 #2558: Ford_SYSR：FS_REQ0038_V3 Welcome/Farewell Fade Activation Signals: 完成涛陆
09:53 功能 #2557: Ford_SYSR：FS_REQ0037_V1 PWM channel Welcome/Farewell Activation: 未完成涛陆
09:52 功能 #2556: Ford_SYSR：FS_REQ0036_V2 DRL Welcome/Farewell Activation: 完成涛陆
09:52 功能 #2555: Ford_SYSR：FS_REQ0035_V1 Static Bending Light Activation: 未完成涛陆
09:52 功能 #2554: Ford_SYSR：FS_REQ0034_V1 Side marker Activation: 未完成涛陆
09:51 功能 #2553: Ford_SYSR：FS_REQ0033_V1 Cornering Activation: 未完成涛陆
09:49 功能 #2552: Ford_SYSR：FS_REQ0032_V1 Front Fog Activation: 未完成涛陆
09:49 功能 #2551: Ford_SYSR：FS_REQ0031_V2_Licoln Lit Star Activation: 未完成涛陆
09:48 功能 #2550: Ford_SYSR：FS_REQ0030_V1 DRL Response to Flash-To-Pass Activation: 完成涛陆
09:46 功能 #2548: Ford_SYSR：FS_REQ0028_V1 DRL Response to Low Beam outage: 完成涛陆
09:44 功能 #2547: Ford_SYSR：FS_REQ0027_V1 DRL EEL LIN command Table: 完成涛陆
09:43 功能 #2546: Ford_SYSR：FS_REQ0026_V2 DRL Control Strategy: 完成涛陆
09:43 功能 #2545: Ford_SYSR：FS_REQ0025_V3 Turn Indicator Feedback: 完成涛陆
09:42 功能 #2544: Ford_SYSR：FS_REQ0024_V1 Turn Indicator Delay: 未完成涛陆
09:42 功能 #2543: Ford_SYSR：FS_REQ0023_V3 Turn Indicator Activation: 7V无法采样，其他功能完成涛陆
09:39 功能 #2542: Ford_SYSR：FS_REQ0022_V2 High Beam EEL Front Fog Activation Reaction: 未完成涛陆
09:37 功能 #2541: Ford_SYSR：FS_REQ0021_V1 High Beam EEL LIN Flash-to-Pass Activation: 完成涛陆
09:36 功能 #2540: Ford_SYSR：FS_REQ0020_V1 High Beam LDM standard ramping: 完成涛陆
09:36 功能 #2539: Ford_SYSR：FS_REQ0019_V1 High Beam (HB) HCM EEL LIN Activation(Not in LDM4 scope): 完成涛陆
09:35 功能 #2538: Ford_SYSR：FS_REQ0018_V1 High Beam (HB) BCM EEL LIN Activation: 完成涛陆
09:35 功能 #2537: Ford_SYSR：FS_REQ0017_V2 LB Activation: 该PIN未IO口，无法采样电压涛陆
09:33 功能 #2535: Ford_SYSR：FS_REQ0015_V2 Low Side Driver 1 and 2 usage Configuration: 除了SBL，其他功能已完成涛陆
09:32 功能 #2534: Ford_SYSR：FS_REQ0014_V1 Low Side Driver 1 and 2 Channel Configuration: 未完成涛陆
09:31 功能 #2533: Ford_SYSR：FS_REQ0013_V1 Channel 2 to 4 Functional Configuration: 完成涛陆
09:31 功能 #2532: Ford_SYSR：FS_REQ0012_V1 DRL Failsafe Mode: 需求取消，该硬线改为信号线涛陆
09:30 功能 #2531: Ford_SYSR：FS_REQ0011_V3 Turn Indicator Failsafe Mode: 完成涛陆
09:29 功能 #2530: Ford_SYSR：FS_REQ0010_V1 Channel 1 Failsafe Mode: 部分完成
以下列表已完成
> |Function |Failsafe Requirement|
> |LB Light Output |Required|
> |LB Thermal Derating |Required|
... 涛陆
09:28 功能 #2519: Ford_SYSR: System Requirement: 完成涛陆
09:27 功能 #2528: Ford_SYSR：FS_REQ0008_V1 Side Detection: 完成涛陆
09:27 功能 #2527: Ford_SYSR：FS_REQ0007_V1 TI Power Mode: 完成涛陆
09:27 功能 #2526: Ford_SYSR：FS_REQ0006_V1 DRL/PO Power supply: 完成涛陆
09:26 功能 #2525: Ford_SYSR：FS_REQ0005_V1 Channel 2(Main) Power Mode: 与软件无关涛陆

2024-10-24

20:19 功能 #2607 (已关闭): Ford_SYSR：FS_REQ0086_V1 LDM Factory Mode: To protect headlamp damage from over/unexpected current of default LDM Dataset configuration in Tier1 plant or other ... 玉洁金
20:17 功能 #2606 (进行中): Ford_SYSR：FS_REQ0085_V1 Ford Functional Safety: The LDM shall meet the functional safety requirements for each of following ASIL rated features:
|_.Item ID|_.Item n... 玉洁金
20:14 功能 #2605 (已关闭): Ford_SYSR：FS_REQ0084_V2 Software Flashing: The LDM SW and parameters shall be flashable via Lin bus acc. to ‘SWDL 00.06.15.002-006’. Please consider that the LI... 玉洁金
20:14 功能 #2604 (已关闭): Ford_SYSR：FS_REQ0083_V1 MSB vs. LSB: In some LIN frames the message is distributed over more than one byte. In every case the frame shall be read as the f... 玉洁金
20:13 功能 #2603 (已关闭): Ford_SYSR：FS_REQ0082_V1 Supplier Defined: Service Return and Development Reporting: For supplier use in development of the LDM and for analysis of warranty service return parts, the supplier should imp... 玉洁金
20:12 功能 #2602 (已关闭): Ford_SYSR：FS_REQ0081_V1 Supplier Defined: Lamp Manufacturing: LDM needs to support Dataset flashing on Ford Manufacturing. 玉洁金
20:11 功能 #2601 (新建): Ford_SYSR：FS_REQ0080_V2 LDM Self-Test Description: In the case a “cycle all” is requested the LDM shall illuminate the following outputs in 3 seconds with the following... 玉洁金
20:10 功能 #2600 (新建): Ford_SYSR：FS_REQ0079_V2 Self-Test Frame: This diagnostic LF/RF_EEL_LoadTest frame includes a cycle all load test. This test allows the definition of an activa... 玉洁金
20:09 功能 #2599 (已关闭): Ford_SYSR：FS_REQ0078_V1 LIN Part Number Reporting: Since we are limited to only 7 bytes of data (besides the LIN Status Byte), transmitting a 23 character part number w... 玉洁金
19:58 功能 #2598 (已关闭): Ford_SYSR：FS_REQ0077_V3 Run Time Configuration Validation: The Front LDM modules will check the configuration data index to that broadcast by the BCM. BCM Command Frame 2 conta... 玉洁金
19:57 功能 #2597 (已关闭): Ford_SYSR：FS_REQ0076_V1 LDM Configuration Monitoring: -The LF_EEL and RF_EEL will support monitoring of BCM Configuration and confirm it matches the vehicle programmed val... 玉洁金
19:56 功能 #2596 (已关闭): Ford_SYSR：FS_REQ0075_V1 Configuration Support: BCM will support configuration of the LIN nodes using the established methods for configuration that are already in p... 玉洁金
19:56 功能 #2595 (已关闭): Ford_SYSR：FS_REQ0074_V2 LIN Configuration Frame Definition: !clipboard-202411011314-1kq8r.png!
Table 40: BCM Front EEL Configuration Frame
!clipboard-202411011315-4n6yy.png!
... 玉洁金
19:55 功能 #2594 (已关闭): Ford_SYSR：FS_REQ0073_V1 Node Lighting Module Configuration Mechanics: Configuring a LIN Node is not a download. It uses a functional message to transfer data one time to the LIN node. The... 玉洁金
19:44 功能 #2593 (已关闭): Ford_SYSR：FS_REQ0072_V1 Node Lighting Module Configuration: Configuration of the LIN Nodes can be accomplished through multiple mechanisms, in vehicle or subassembly electrical ... 玉洁金
19:44 功能 #2592 (已关闭): Ford_SYSR：FS_REQ0071_V1 Description of Node Reporting: SAE J2602 Status Byte
In J2602, the very first byte transmitted by any node is the LIN Status Byte. It has this form... 玉洁金
19:37 功能 #2591 (新建): Ford_SYSR：FS_REQ0070_V2 BCM EEL VO Load Sequencing: The following command message is used to actuate each load individually. The LDM shall only consider LF EEL and RF EE... 玉洁金
19:35 功能 #2590 (已关闭): Ford_SYSR：FS_REQ0069_V1 BCM EEL LDM Node Status Report Frame: The following frame describes the signals being reported by the LDM
• Name: Node Status Message
• Size: 8 Byte
• T... 玉洁金
19:32 功能 #2589 (已关闭): Ford_SYSR：FS_REQ0068_V1 Exterior Lighting Functional Support: Many of the signals defined in the Command Frames provide functionality that appear to overlap and do to some extent.... 玉洁金
19:24 功能 #2588 (已关闭): Ford_SYSR：FS_REQ0067_V1 BCM EEL Command Frame 2: The following is the second frame from the BCM providing commands and state information used by the LDM.

o Name:... 玉洁金
19:20 功能 #2587 (已关闭): Ford_SYSR：FS_REQ0066_V1 BCM EEL Command Frame 1: The following is the first frame from the BCM providing commands and state information used by the LDM.

o Name: ... 玉洁金
19:19 功能 #2586 (已关闭): Ford_SYSR：FS_REQ0065_V1 EEL LIN Identifier Allocation: The following tables list the address assignments, the message publisher and target recipient for the message data. ... 玉洁金
19:16 功能 #2585 (已关闭): Ford_SYSR：FS_REQ0064_V1 EEL LIN Message Sequencing: The following diagram illustrates the LIN messaging sequence for the BCM EEL LIN Bus. The BCM will alternate between ... 玉洁金
19:16 功能 #2584 (已关闭): Ford_SYSR：FS_REQ0063_V2 LDF: The LDM shall consider LDF BCM_G2_LIN_05_Ckt_v17_2016Dec01.LDF when on BCM LIN (10,417 baud).
!clipboard-20241024191... 玉洁金
19:14 功能 #2583 (已关闭): Ford_SYSR：FS_REQ0062_V2 LDM diagnostic with test command: LDM shall support diagnostic capability to read the configuration and fault status with specific engineering diagnost... 玉洁金
19:13 功能 #2582 (已关闭): Ford_SYSR：FS_REQ0061_V3 Failure Recover strategy: All the LDM failure above in this chapter shall recovery when:
• LED load returns to normal operation(N-x except, N-... 玉洁金
19:11 功能 #2581: Ford_SYSR：FS_REQ006x_V2 LB Activation Redundant: To enhance the LB fault handling capability under FUSA TSR 1.4.2 requirement, currently LB hardwire is used as activa... 玉洁金
19:05 功能 #2581 (已关闭): Ford_SYSR：FS_REQ006x_V2 LB Activation Redundant: To enhance the LB fault handling capability under FUSA TSR 1.4.2 requirement, to adopt LB hardwire or LIN signal “Hea... 玉洁金
19:02 功能 #2580 (已关闭): Ford_SYSR：FS_REQ0060_V1 LIN Bus Failures: The Network shall meet the requirements as defined per the following failure modes:
• LDM Power Loss – LDM shall not... 玉洁金
19:01 功能 #2579 (已关闭): Ford_SYSR：FS_REQ0059_V1 LIN Lost: In case of “LIN lost”, the LDM shall continue functioning. A “LIN lost” situation occurs if:
• 5000 mS (+/- 50mS) no... 玉洁金
18:59 功能 #2578 (已关闭): Ford_SYSR：FS_REQ0058_V1 NTC Thermistor Failure: If the NTC resistor is lost or its value out is of range(<-40°C || >150°C), then corresponding channels shall be driv... 玉洁金
18:58 功能 #2577 (已关闭): Ford_SYSR：FS_REQ0057_V1 Binning Resistor Lost or Out of Range: If the binning resistor is lost (short circuit or open circuit) or out of range, it shall not cause overcurrent excee... 玉洁金
18:57 功能 #2576 (已关闭): Ford_SYSR：FS_REQ0056_V1 Buck Failure Detection: The failures that the buck itself detects are the followings:
o Short to GND
o Short to battery in HSD when it i... 玉洁金
18:57 功能 #2575 (已关闭): Ford_SYSR：FS_REQ0055_V3 LDM Failure Response Reporting: If failure occurs, the LED voltage, LDM temperature and failure time shall be saved and reported. The last five error... 玉洁金
18:56 功能 #2574 (已关闭): Ford_SYSR：FS_REQ0054_V1 Load Failure Response Deactivation: LED outage detection shall work within -40 to 110°C ambient temperature range. Input voltage range for LED outage det... 玉洁金
18:55 功能 #2573 (已关闭): Ford_SYSR：FS_REQ0053_V2 General LED Failure Detection: The LDM must support outage detection on all output channels. Outage detection will only occur while the channel is o... 玉洁金
18:54 功能 #2572 (已关闭): Ford_SYSR：FS_REQ0052_V1_LED Thermal Derating Smooth Appearance: The LDM shall thermal dim at a rate no greater than 2.5%/sec for thermal derating purposes to provide a smooth lighti... 玉洁金
18:53 功能 #2571 (已关闭): Ford_SYSR：FS_REQ0051_V1 NTC Calculation: Selection of the NTC is the responsibility of the headlamp supplier. The LDM shall be capable of supporting a wide va... 玉洁金
18:51 功能 #2570 (已关闭): Ford_SYSR：FS_REQ0050_V2 LDM intermal Thermal Derating: The LDM shall have an internal NTC thermistor and monitor temperatures critical to operation. To avoid stressing the ... 玉洁金
18:47 功能 #2569 (已关闭): Ford_SYSR：FS_REQ0049_V2 Output Thermal Derating curve: All output functions shall have a defined derating curves using 5 points described by a temperature and a percent der... 玉洁金
18:46 功能 #2568 (已关闭): Ford_SYSR：FS_REQ0048_V1 Thermal Monitoring: The LDM must monitor the headlamp PCBA temperatures with NTC thermistors to thermally derate LED functions current to... 玉洁金
18:45 功能 #2567 (已关闭): Ford_SYSR：FS_REQ0047_V1 LED Thermal Derating: The LDM shall control the LED junction temperature by controlling the current to the LED via peak current derating. I... 玉洁金
18:43 功能 #2566 (已关闭): Ford_SYSR：FS_REQ0046_V1 Fan Failure Detection: According to the content of the configuration parameter ‘Fan_Outage_Detect_cfg’, the LDM will either perform full sta... 玉洁金
18:41 功能 #2565 (已关闭): Ford_SYSR：FS_REQ0045_V2 Activation of the Fan: The activation of FAN can be configured by the parameter ‘FAN_Activation_Trigger_cfg’.
• 0x00: No FAN
• 0x01:Activa... 玉洁金
18:40 功能 #2564 (已关闭): Ford_SYSR：FS_REQ0044_V1 FAN Functional self-test when power on: After power on of the LDM, the fan will be activated for specific amount of time to do the functional test.The time c... 玉洁金
18:40 功能 #2563 (已关闭): Ford_SYSR：FS_REQ0043_V2 Bin Class Current Setting: BIN current can be set for BIN0 to BIN7 of each channel in the configuration parameter file, the current range should... 玉洁金
18:38 功能 #2562 (已关闭): Ford_SYSR：FS_REQ0042_V2 Binning Resistor: The LDM shall be capable of supporting a binning resistor input for each channel to set the current for the correspon... 玉洁金
18:35 功能 #2561 (已关闭): Ford_SYSR：FS_REQ0041_V2 Channel output intensity Smooth Fading: No ramping is required between 0 and 5%, 8 bit resolution is required. A non-linear ramp per Steven’s Power Law shall... 玉洁金
18:33 功能 #2560 (已关闭): Ford_SYSR：FS_REQ0040_V1 Light Source Activation Latency Times: The LDM shall be capable of activating each function within the times provided below. Latency time refers to activati... 玉洁金
18:30 功能 #2559 (已关闭): Ford_SYSR：FS_REQ0039_V2 Fading Requirements: | |Channel 1 |Channel 2 |Channel 3 |Channel 4 |LSD1&2|
|Fade-in capability from 0% onwards |Yes |Yes |Yes |Yes... 玉洁金
18:27 功能 #2558 (已关闭): Ford_SYSR：FS_REQ0038_V3 Welcome/Farewell Fade Activation Signals: The Welcome/Farewell activation shall be triggered by the LIN command ‘WFSubstate’ in both ‘BCM_E_FC1’ and‘BCM_E_FC2’... 玉洁金
18:24 功能 #2557 (已关闭): Ford_SYSR：FS_REQ0037_V1 PWM channel Welcome/Farewell Activation: PWM channels shall be also capable to be used during Welcome/Farewell sequence, according to above ‘PWMx_Function_Ass... 玉洁金
18:23 功能 #2556 (已关闭): Ford_SYSR：FS_REQ0036_V2 DRL Welcome/Farewell Activation: When the LDM is triggered to fade on for embrace, the LDM shall fade from 0% to the duty cycle given by ‘DRL_Embrace_... 玉洁金
18:22 功能 #2555 (已关闭): Ford_SYSR：FS_REQ0035_V1 Static Bending Light Activation: The static bending light (SBL) will be activated based on steering wheel angle provided by the Signal ‘SteAngle’ and ... 玉洁金
18:22 功能 #2554 (已关闭): Ford_SYSR：FS_REQ0034_V1 Side marker Activation: The activation/deactivation of side marker light shall be triggered by BCM LIN command ‘Position_Park_Left/Right_Cmd’... 玉洁金
18:21 功能 #2553 (已关闭): Ford_SYSR：FS_REQ0033_V1 Cornering Activation: The activation/deactivation of cornering light shall be triggered by BCM LIN command ‘Cornering_cmd’ with the LDM sid... 玉洁金
18:20 功能 #2552 (已关闭): Ford_SYSR：FS_REQ0032_V1 Front Fog Activation: The activation/deactivation of front fog light shall be triggered by BCM LIN command ‘Front_Fog_Request’.
‘Front_F... 玉洁金
18:20 功能 #2551 (已关闭): Ford_SYSR：FS_REQ0031_V2_Licoln Lit Star Activation: The activation/deactivation of Licoln Star shall be triggered by BCM LIN command ‘Position_Park_Left/Right_Cmd’ with ... 玉洁金
18:19 功能 #2550 (已关闭): Ford_SYSR：FS_REQ0030_V1 DRL Response to Flash-To-Pass Activation: If the DRL is active, and flash to pass signal is received via LIN and IGN is either run or start, the LDM shall foll... 玉洁金
18:06 功能 #2548 (已关闭): Ford_SYSR：FS_REQ0028_V1 DRL Response to Low Beam outage: DRL maybe affected by LB if LB outage is detected and configured to be turned off, a configurable parameter “DRL_LB_O... 玉洁金
18:06 功能 #2547 (已关闭): Ford_SYSR：FS_REQ0027_V1 DRL EEL LIN command Table: The output of the dedicated LIN controlled DRL/Position function shall be determined based on the following LIN signa... 玉洁金
18:03 功能 #2546 (已关闭): Ford_SYSR：FS_REQ0026_V2 DRL Control Strategy: The module will be capable of determining DRL state by either BCM LIN or by BCM ‘L/RF_DRL_LAMP_Ckt’ direct wire.
... 玉洁金
18:02 功能 #2545 (已关闭): Ford_SYSR：FS_REQ0025_V3 Turn Indicator Feedback: Under normal operating conditions, the LDM shall report Turn indicator status to the BCM by outputting the received s... 玉洁金
18:01 功能 #2544 (已关闭): Ford_SYSR：FS_REQ0024_V1 Turn Indicator Delay: The LDM shall support a configurable delay time of the turn indicator to be able to synchronize with other turn indic... 玉洁金
18:01 功能 #2543 (已关闭): Ford_SYSR：FS_REQ0023_V3 Turn Indicator Activation: For the definition of the operational state of the Turn Indicator, the voltage level of the Turn supply terminal of t... 玉洁金
17:59 功能 #2542 (已关闭): Ford_SYSR：FS_REQ0022_V2 High Beam EEL Front Fog Activation Reaction: The parameter ‘HB_combined_Front_fog_cfg’ describes the handling of HB deactivation in case of front fog activation. ... 玉洁金
17:58 功能 #2541 (已关闭): Ford_SYSR：FS_REQ0021_V1 High Beam EEL LIN Flash-to-Pass Activation: In the event the LIN signal ‘FTP_Status’ transitions from ‘0’ to ‘1’, the high beam output(s) shall activate immediat... 玉洁金
17:57 错误 #2515 (已解决): 需求确认: 盛炜朱
17:56 错误 #2515: 需求确认: !
!clipboard-202410241756-fie2e.png!
! 盛炜朱
14:17 错误 #2515 (已关闭): 需求确认: 当我配置LB_ Failure_Report_cfg/HB_ Failure_Report_cfg/DRL_ Failure_Report_cfg都为disable的时候，APINF2和APINFO3是否都需要置一，现在有个这个问题，... 传鹏胡
17:57 功能 #2540 (已关闭): Ford_SYSR：FS_REQ0020_V1 High Beam LDM standard ramping: The LDM shall also have the option to select a standard LDM ramping time within parameters. To do this the parameter ... 玉洁金
17:56 功能 #2539 (已关闭): Ford_SYSR：FS_REQ0019_V1 High Beam (HB) HCM EEL LIN Activation(Not in LDM4 scope): In FNV2 HCM configuration the corresponding HCM HB commands will also activate the HB and/or HB2 as requested by ‘LDM... 玉洁金
17:55 功能 #2538 (已关闭): Ford_SYSR：FS_REQ0018_V1 High Beam (HB) BCM EEL LIN Activation: High beam (of any type) shall only activate if IGN is in Run or Start.
The high beam function shall be capable of ... 玉洁金
17:54 功能 #2537 (已关闭): Ford_SYSR：FS_REQ0017_V2 LB Activation: For the definition of the operational state of the LB, the voltage level of the LB supply terminal of the BCM (‘L/RF_... 玉洁金
17:54 功能 #2536 (已关闭): Ford_SYSR：FS_REQ0016_V3 PWM output configuration: The LDM shall have 4 PWM outputs capable of controlling any of the following functions via configure parameter ‘PWMx_... 玉洁金
17:53 功能 #2535 (已关闭): Ford_SYSR：FS_REQ0015_V2 Low Side Driver 1 and 2 usage Configuration: The function of the Low Side driver shall also be configurable. The low side driver activation shall then be based o... 玉洁金
17:51 功能 #2534 (已关闭): Ford_SYSR：FS_REQ0014_V1 Low Side Driver 1 and 2 Channel Configuration: Additional secondary functions may be added any of the 4 channels (including channel 1) using one of the 2 low side d... 玉洁金
17:49 功能 #2533 (已关闭): Ford_SYSR：FS_REQ0013_V1 Channel 2 to 4 Functional Configuration: Channel 2 to 4 shall be capable of supporting the following functions based on the parameters “Channel2/3/4_usage_cfg... 玉洁金
17:48 功能 #2532 (已关闭): Ford_SYSR：FS_REQ0012_V1 DRL Failsafe Mode: The input will be active in BCM failsafe mode, and only under DRL hardwire control condition, the DRL and all corresp... 玉洁金
17:45 功能 #2531 (已关闭): Ford_SYSR：FS_REQ0011_V3 Turn Indicator Failsafe Mode: The input will be active in BCM failsafe mode, and therefore the TI and all corresponding main functions of the TI sh... 玉洁金
17:43 功能 #2530 (已关闭): Ford_SYSR：FS_REQ0010_V1 Channel 1 Failsafe Mode: The channel1 input will be active in BCM failsafe mode, and LB and all corresponding main functions of the LB shall b... 玉洁金
17:39 功能 #2529 (已关闭): Ford_SYSR：FS_REQ0009_V1 Channel 1 output Assignment: The high side assignment of channel 1 must be base low beam in all cases. This shall not be configurable via LDM para... 玉洁金
17:38 功能 #2528 (已关闭): Ford_SYSR：FS_REQ0008_V1 Side Detection: The LDMs will be used on a single LIN bus and needs to have defined mounting position information. To keep the LDM pa... 玉洁金
17:30 功能 #2527 (已关闭): Ford_SYSR：FS_REQ0007_V1 TI Power Mode: Power for Turn indicator prefer to be apply to the “Power Supply Channel 3” input.
In the case channel 3 is sourced... 玉洁金
17:29 功能 #2526 (已关闭): Ford_SYSR：FS_REQ0006_V1 DRL/PO Power supply: DRL/PO input can be supplied with two different modes:
1) a PWM signal from BCM direct wire ‘L/RF_DRL_LAMP_Ckt’ to p... 玉洁金
17:28 功能 #2525 (已关闭): Ford_SYSR：FS_REQ0005_V1 Channel 2(Main) Power Mode: Channel 2 input (Main Power Feed) will be supplied with a steady state power supply from the vehicle to be considered... 玉洁金
17:26 功能 #2524 (已关闭): Ford_SYSR：FS_REQ0004_V1 Channel 1 Power Mode: The LDM Channel 1 output shall be triggered by BCM Low Beam Circuit(L/RF_Low_Beam_Ckt) as described in Figure 3.
A... 玉洁金
17:24 功能 #2523 (已关闭): Ford_SYSR：FS_REQ0003_V2 Channel power source Configuration: |Channel No. |Channelx_ Power_Source_cfg|
|Channel 1 |BCM LB (L/RF-Low_Beam_Ckt)|
|Channel 2 |Relay connected to... 玉洁金
17:03 功能 #2522 (已关闭): Ford_SYSR：FS_REQ0002_V1 LDM Input Transients: The LDM will be expected to withstand input transients described by:
• FMC1278 - Electromagnetic Compatibility Spec... 玉洁金
16:03 功能 #2520 (已关闭): Ford_SYSR: FS_REQ0001_V2 LDM Input: The LDM will use Channel2 as main power input as HS REQ005, and rest channels input to be used as an input signal to ... 斌徐
15:58 功能 #2519 (已关闭): Ford_SYSR: System Requirement: -FS_LDM Localization_V2.0.docx-
FS_LDM Localization_V2.6.docx
HS_LDM Localization_V2.2.docx 斌徐
14:54 Task #2516 (已关闭): Ford_SWET: Static code analysis: Application software Static code analysis(S00071691.7) 斌徐

2024-10-23

16:53 Bug #2514 (Bug-已关闭): HB呼吸问题: HB的Fade speed配置为slow（4000ms），实际没有4000ms 传鹏胡
16:11 Bug #2513 (Bug-问题回归验证): 单元测试测试问题反馈: 1.app_dpl 代码最后存在PWM重复赋值计算，需删除
2.app_fan fan状态为error时，fan赋值错误，未停止fan，需分析修改槐杨
16:04 Task #2509: Ford_SWET: DV&PV Software Test: 完成A001.6版本单元测试，静态测试，LIN一致性测试及报告更新
等待A001.8版本发布槐杨
15:59 Bug #2512 (Bug-已关闭): 工厂模式在有app，boot和dataset的时候，刷app后，dataset会被冲掉变成空白: 在工厂模式下，有BOOT，APP,dataset的时候，再次刷写APP，原先的dataset会被冲掉，在读dataset的版本会变成空白传鹏胡
15:49 Bug #2511 (Bug-已关闭): 退出低功耗模式无法正常点灯: 电源上电，不给任何逻辑，进入低功耗，在上任意逻辑，对应功能点不亮传鹏胡

2024-10-22

10:30 Task #2510 (进行中): Ford_Fusa: function Safety SSR: Complete and sign Fusa SSR documents with Ford team 斌徐
10:28 Task #2509 (已关闭): Ford_SWET: DV&PV Software Test: Ford LDM Function Test 斌徐
10:26 Task #2508 (已关闭): Ford_SWED: DV&PV Software Release: Release Software for DV/PV test:
Boot loader Software Version：SW0007170.B001
Application Software Version：SW0007169... 斌徐

导出 Atom

项目

一般

简介

FORD LDM Localization

活动

活动

2024-10-28

2024-10-27

2024-10-25

2024-10-24

2024-10-23

2024-10-22