FORD LDM Localization

2024-10-27

17:04 功能 #2655 (已关闭): Ford_SWER_0015_0001：Low Side Driver 1 and 2 usage Configuration(Dataset_Lsd_usage)

Dataset应该可以通过“LSD1/2_usage_cfg”，配置LSD的功能，并生成对应的数据。
(Dataset should be able to configure LSD functions and generate d... 培源 左

15:55 功能 #2654 (已关闭): Ford_SWER_0014_0006：Low Side Driver 1 and 2 Channel Configuration(LSD assignment Channel4)

APP读取Dataset的生成数据，若“LSD1/2_channel_assignment_cfg”为0x04，
则对应LSD连接Channel4输出。
(The APP reads the generated data from... 培源 左

15:54 功能 #2653 (已关闭): Ford_SWER_0014_0005：Low Side Driver 1 and 2 Channel Configuration(LSD assignment Channel3)

APP读取Dataset的生成数据，若“LSD1/2_channel_assignment_cfg”为0x03，
则对应LSD连接Channel3输出。
(The APP reads the generated data from... 培源 左

15:53 功能 #2652 (已关闭): Ford_SWER_0014_0004：Low Side Driver 1 and 2 Channel Configuration(LSD assignment Channel2)

APP读取Dataset的生成数据，若“LSD1/2_channel_assignment_cfg”为0x02，
则对应LSD连接Channel2输出。
(The APP reads the generated data from... 培源 左

15:44 功能 #2648 (已关闭): Ford_SWER_0014_0003：Low Side Driver 1 and 2 Channel Configuration(LSD assignment Channel1)

APP读取Dataset的生成数据，若“LSD1/2_channel_assignment_cfg”为0x01，
则对应LSD连接Channel1输出。
(The APP reads the generated data from... 培源 左

15:41 功能 #2647 (已关闭): Ford_SWER_0014_0002：Low Side Driver 1 and 2 Channel Configuration(LSD Not used)

APP读取Dataset的生成数据，若“LSD1/2_channel_assignment_cfg”为0x00，
则对应LSD不启用，不会联动任何通道输出。
(The APP reads the generated data fr... 培源 左

15:34 功能 #2646 (已关闭): Ford_SWER_0014_0001：Low Side Driver 1 and 2 Channel Configuration(Dataset Cfg)

Dataset需要通过“LSD1/2_channel_assignment_cfg”配置项，来配置LSD连接到哪个通道或者不启用，并生成以下对应数据。
(The Dataset uses the LSD1/2_channel_ass... 培源 左

2024-10-25

16:37 功能 #2645 (已关闭): Ford_SWER_0013_0006：Channel 2 to 4 Functional Configuration（TI）

APP读取Dataset的生成数据，若“Channel2/3/4_usage_cfg”为0x04，
则对应通道只应响应Turn Indicator信号输出。
(The APP reads the generated data fr... 培源 左

16:36 功能 #2644 (已关闭): Ford_SWER_0013_0005：Channel 2 to 4 Functional Configuration（DRL）

APP读取Dataset的生成数据，若“Channel2/3/4_usage_cfg”为0x03，
则对应通道只应响应DRL信号输出。
(The APP reads the generated data from the Data... 培源 左

16:35 功能 #2643 (已关闭): Ford_SWER_0013_0004：Channel 2 to 4 Functional Configuration（HB）

APP读取Dataset的生成数据，若“Channel2/3/4_usage_cfg”为0x02，
则对应通道只应响应HB信号输出。
(The APP reads the generated data from the Datas... 培源 左

16:34 功能 #2642 (已关闭): Ford_SWER_0013_0003：Channel 2 to 4 Functional Configuration（LB）

APP读取Dataset的生成数据，若“Channel2/3/4_usage_cfg”为0x01，
则对应通道只应响应LB信号输出。
(The APP reads the generated data from the Datas... 培源 左

16:32 功能 #2641 (已关闭): Ford_SWER_0013_0002：Channel 2 to 4 Functional Configuration（Not used）

APP读取Dataset的生成数据，若“Channel2/3/4_usage_cfg”为0x00，
则对应通道不被启动，任何情况都不应该输出。
(The APP reads the generated data from the ... 培源 左

16:26 功能 #2640 (已关闭): Ford_SWER_0013_0001：Channel 2 to 4 Functional Configuration（Dataset配置）

Dataset中应该支持将“Channel2/3/4_usage_cfg”参数，配置为以下功能，并生成对应的数据。
(The Dataset should support setting the Channel2/3/4_usage... 培源 左

16:08 功能 #2639 (已关闭): Ford_SWER_0011_0007：Turn Indicator Failsafe Mode（TI Feedback）

软件进入到Failsafe Mode，且识别到有“TI Power supply Channel”(L/RF_Turn_Lamp_Ckt)使能，同时读取到Dataset中“TI_POWER_Source_CFG”配置为0x01,“Ch... 培源 左

16:06 功能 #2638 (已关闭): Ford_SWER_0011_0006：Turn Indicator Failsafe Mode（Active Load Fault Reporting via LIN）

软件进入到Failsafe Mode，且识别到有“TI Power supply Channel”(L/RF_Turn_Lamp_Ckt)使能，同时读取到Dataset中“TI_POWER_Source_CFG”配置为0x01,“Ch... 培源 左

15:44 功能 #2637 (已关闭): Ford_SWER_0011_0005：Turn Indicator Failsafe Mode（N-1 Failure Detection）

软件进入到Failsafe Mode，且识别到有“TI Power supply Channel”(L/RF_Turn_Lamp_Ckt)使能，同时读取到Dataset中“TI_POWER_Source_CFG”配置为0x01,“Ch... 培源 左

15:41 功能 #2636 (已关闭): Ford_SWER_0011_0004：Turn Indicator Failsafe Mode（Channel Open/Short Detection）

软件进入到Failsafe Mode，且识别到有“TI Power supply Channel”(L/RF_Turn_Lamp_Ckt)使能，同时读取到Dataset中“TI_POWER_Source_CFG”配置为0x01,“Ch... 培源 左

15:37 功能 #2635 (已关闭): Ford_SWER_0011_0003：Turn Indicator Failsafe Mode（TI Bin Sense）

软件进入到Failsafe Mode，且识别到有“TI Power supply Channel”(L/RF_Turn_Lamp_Ckt)使能，同时读取到Dataset中“TI_POWER_Source_CFG”配置为0x01,“Ch... 培源 左

15:35 功能 #2634 (已关闭): Ford_SWER_0011_0002：Turn Indicator Failsafe Mode（TI Thermal Derating）

软件进入到Failsafe Mode，且识别到有“TI Power supply Channel”(L/RF_Turn_Lamp_Ckt)使能，同时读取到Dataset中“TI_POWER_Source_CFG”配置为0x01,“Ch... 培源 左

15:16 功能 #2633 (已关闭): Ford_SWER_0011_0001：Turn Indicator Failsafe Mode（TI Light Output）

软件进入到Failsafe Mode，且识别到有“TI Power supply Channel”(L/RF_Turn_Lamp_Ckt)使能，同时读取到Dataset中“TI_POWER_Source_CFG”配置为0x01,“Ch... 培源 左

15:13 功能 #2632 (已关闭): Ford_SWER_0007_0002: 转向灯触发信号规格

转向灯触发信号是1.33Hz, 50%占空比;(375ms) 盛炜 朱

15:12 功能 #2631 (已关闭): Ford_SWER_0007_0001: 转向灯触发方式

Dataset中TI功能触发通道可以配置为“Power Supply Channel 3”或无效，并生成对应的数据。
(The TI function trigger Channel in the Dataset can be co... 盛炜 朱

15:10 功能 #2625: Ford_SWER_0051_0001：NTC temperature to resistance

add R,R0,B,T0 and T description
R = NTC Resistance at T (Ω)
R0 = Resistance at T0 (Ω)
B = NTC B – Constant value (... 涛 陆

14:53 功能 #2625 (已关闭): Ford_SWER_0051_0001：NTC temperature to resistance

The software shall calculate NTC resistors value by configuring the R0 and B-constant of the thermistor within the LD... 涛 陆

15:10 功能 #2630 (已关闭): Ford_SWER_0006_0001: DRL/PO触发方式

"DRL/PO"有两种控制来源:
1. "BCM"硬线发送"PWM控制信号"
2. "BCM" "LIN命令"DRL_Rqst"
Dataset中可配置DRL/PO的控制方式 盛炜 朱

15:07 功能 #2629 (已关闭): Ford_SWER_0010_0009：Channel 1 Failsafe Mode(Channels 2-4 Assigned to LB)

软件识别到Input Channel1（L/RF_Low_Beam_Ckt）使能且main power失效（Input Channel 2失效）时，
如果Output Channel2、3、4被配置成LB功能，该部分输出通道禁止输出... 培源 左

15:06 功能 #2628 (已关闭): Ford_SWER_0005_0001：输入通道2供电模式

输入通道2是主供电, 能够通过AD端口，识别电压范围。
当Input CHN2丢失,但LDM通过Input CHN1/CHN3/CHN4获电,则LDM需要通过LIN通讯对外报如下故障:
!clipboard-202411011... 盛炜 朱

15:04 功能 #2627 (已关闭): Ford_SWER_0010_0008：Channel 1 Failsafe Mode(Light Connected to CH1 Low Side Driver)

软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
连接到Output Channel1的低边部分灯不可被点亮。
(When the software ent... 培源 左

14:59 功能 #2626 (已关闭): Ford_SWER_0010_0007：Channel 1 Failsafe Mode(Static Bending)

软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
Static Bending不可被点亮。
(When the software enters Failsa... 培源 左

14:52 功能 #2624 (已关闭): Ford_SWER_0010_0006：Channel 1 Failsafe Mode(Active Load Fault Reporting via LIN)

软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
若读取到Dataset生成的数据配置有LB故障上报功能，Output Channel1的LB需要能满足Act... 培源 左

14:50 功能 #2623 (已关闭): Ford_SWER_0010_0005：Channel 1 Failsafe Mode(N-1 Failure Detection)

软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
若读取到Dataset生成的数据中“LB_Failure_Deact_cfg”配置为0x01/0x02时，O... 培源 左

14:44 功能 #2522: Ford_SYSR：FS_REQ0002_V1 LDM Input Transients

非软件需求, 需测试注意 盛炜 朱

11:52 功能 #2522 (进行中): Ford_SYSR：FS_REQ0002_V1 LDM Input Transients

玉洁 金

09:24 功能 #2522: Ford_SYSR：FS_REQ0002_V1 LDM Input Transients

完成 涛 陆

14:44 功能 #2524: Ford_SYSR：FS_REQ0004_V1 Channel 1 Power Mode

非软件需求, 测试需注意 盛炜 朱

09:25 功能 #2524: Ford_SYSR：FS_REQ0004_V1 Channel 1 Power Mode

完成 涛 陆

14:39 功能 #2622 (已关闭): Ford_SWER_0052_0001：LED Thermal Derating Smooth Appearance

APP:The LDM shall thermal dim at a rate no greater than 2.5%/sec.
now： rate = 2% 涛 陆

14:37 功能 #2621 (已关闭): Ford_SWER_0010_0004：Channel 1 Failsafe Mode(Channel Open/Short Detection)

软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
Output Channel1的LB需要能满足Channel Open/Short Detection功能。... 培源 左

14:34 功能 #2620 (已关闭): Ford_SWER_0010_0003：Channel 1 Failsafe Mode(LB Bin Sense)

软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
Output Channel1的LB需要能满足LB Bin Sense功能。
(When the soft... 培源 左

14:31 功能 #2619 (已关闭): Ford_SWER_0010_0002：Channel 1 Failsafe Mode(LB Thermal Derating)

软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
Output Channel1的LB需要能满足LB Thermal Derating功能。
(When t... 培源 左

14:27 功能 #2618 (已关闭): Ford_SWER_0001_0005：电源电压采样过滤时间

电源电压采样及过滤时间需要大于 -500- 250ms以避免如EMC实验波形注入导致LED亮度变化. 盛炜 朱

14:24 功能 #2617 (已关闭): Ford_SWER_0010_0001：Channel 1 Failsafe Mode(LB Light Output)

软件进入到Failsafe Mode,且识别到有Input Channel1（L/RF_Low_Beam_Ckt）使能时，
Output Channel1的LB需要正常点亮。
(When the software enters F... 培源 左

14:23 功能 #2616 (已关闭): Ford_SWER_0001_0004：电源电压降功率平滑过渡

电源电压降功率需要采用平滑过渡算法防止亮度突然跳变 盛炜 朱

14:19 功能 #2615 (已关闭): Ford_SWER_0001_0003：电源电压降功率波形

电压缓升和缓降，对于所有功能点亮（前提即main power和LB/TI power电压一致, LIN点灯信号ok），电压缓升时到达7V时HB+DRL/POS以20%（假设最低可承受输出）输出，并保持到8V，LB+TI开始以20%点亮... 盛炜 朱

14:01 功能 #2614 (已关闭): Ford_SWER_0003_0004：Dataset中对于DRL/PO功能的配置

!clipboard-202410291648-bqeje.png!
Dataset中需要能对DRL/PO功能的触发源进行设定
INVALID - 本项目没有DRL/PO功能
InputCHN4 - 通过LDM Input ch... 盛炜 朱

13:40 功能 #2612 (已关闭): Ford_SWER_0003_0003：输入通道3的功能

Dataset中可以将Input Channel3作为TI的输入配置;
APP需要获取Dataset中Input Channel3的配置,当配置为TI功能时,软件需要获取Input Channel3高低电平;当配置为Invalid功... 盛炜 朱

13:25 功能 #2611 (已关闭): Ford_SWER_0003_0002：输入通道2的功能

App需要识别Input Channel2作为主电源是否存在的判断;
Dataset中无需对于Input Channel2做配置项;
上位机需要能读出Input Channel2的电压; 盛炜 朱

13:20 功能 #2610 (已关闭): Ford_SWER_0003_0001：输入通道1的功能

LB功能只绑定在Input channel1上
APP只需要获取Input channel1的高地电平状态经过滤波后即可以判定LB On或者Off;
Dataset无需该条配置项; 盛炜 朱

13:10 功能 #2523: Ford_SYSR：FS_REQ0003_V2 Channel power source Configuration

客户已经更新该条需求,最新需求需结合LDM Localization Dataset_V1.6:
Input Channel 3只能配置为:Invalid或者TI无法配置为DRL
Input Channel 4只能配置为:Inva... 盛炜 朱

11:54 功能 #2523 (进行中): Ford_SYSR：FS_REQ0003_V2 Channel power source Configuration

玉洁 金

09:24 功能 #2523: Ford_SYSR：FS_REQ0003_V2 Channel power source Configuration

需求有变更，按新需求完成 涛 陆

12:43 功能 #2567: Ford_SYSR：FS_REQ0047_V1 LED Thermal Derating

!clipboard-202410251243-cdazp.png!
客户已明确规定150mA以下才能调PWM 盛炜 朱

10:59 功能 #2567: Ford_SYSR：FS_REQ0047_V1 LED Thermal Derating

!clipboard-202410251051-5zxoq.png!
客户解答LED降功率优先降电流,在保证电流精度的最小电流值后调PWM,需要结合硬件实际情况来定具体电流值. 盛炜 朱

10:00 功能 #2567: Ford_SYSR：FS_REQ0047_V1 LED Thermal Derating

完成 涛 陆

12:32 功能 #2520: Ford_SYSR: FS_REQ0001_V2 LDM Input

!clipboard-202410251232-5unp0.png!
盛炜 朱

09:23 功能 #2520: Ford_SYSR: FS_REQ0001_V2 LDM Input

完成 涛 陆

11:04 功能 #2574: Ford_SYSR：FS_REQ0054_V1 Load Failure Response Deactivation

!clipboard-202410251104-7pspv.png!
盛炜 朱

10:06 功能 #2574: Ford_SYSR：FS_REQ0054_V1 Load Failure Response Deactivation

完成 涛 陆

11:01 功能 #2607: Ford_SYSR：FS_REQ0086_V1 LDM Factory Mode

有个bug需要修复 涛 陆

11:00 功能 #2605: Ford_SYSR：FS_REQ0084_V2 Software Flashing

完成 涛 陆

10:59 功能 #2604: Ford_SYSR：FS_REQ0083_V1 MSB vs. LSB

完成 涛 陆

10:57 功能 #2603: Ford_SYSR：FS_REQ0082_V1 Supplier Defined: Service Return and Development Reporting

EDF1完成，EDF2部分完成 涛 陆

10:57 功能 #2563: Ford_SYSR：FS_REQ0043_V2 Bin Class Current Setting

Updated REQ0043 BIN class setting
BIN current can be set for BIN0 to BIN7 of each channel in the configuration param... 玉洁 金

09:57 功能 #2563: Ford_SYSR：FS_REQ0043_V2 Bin Class Current Setting

完成 涛 陆

10:56 功能 #2602: Ford_SYSR：FS_REQ0081_V1 Supplier Defined: Lamp Manufacturing

完成 涛 陆

10:54 功能 #2601: Ford_SYSR：FS_REQ0080_V2 LDM Self-Test Description

未完成 涛 陆

10:54 功能 #2600: Ford_SYSR：FS_REQ0079_V2 Self-Test Frame

未完成 涛 陆

10:52 功能 #2536: Ford_SYSR：FS_REQ0016_V3 PWM output configuration

The LDM shall have 4 PWM outputs capable of controlling any of the following functions via configure parameter ‘PWMx_... 玉洁 金

09:33 功能 #2536: Ford_SYSR：FS_REQ0016_V3 PWM output configuration

部分完成 涛 陆

10:50 功能 #2599: Ford_SYSR：FS_REQ0078_V1 LIN Part Number Reporting

完成 涛 陆

10:49 功能 #2598: Ford_SYSR：FS_REQ0077_V3 Run Time Configuration Validation

完成 涛 陆

10:46 功能 #2597: Ford_SYSR：FS_REQ0076_V1 LDM Configuration Monitoring

完成 涛 陆

10:45 功能 #2596: Ford_SYSR：FS_REQ0075_V1 Configuration Support

BCM LIN功能完成 涛 陆

10:42 功能 #2595: Ford_SYSR：FS_REQ0074_V2 LIN Configuration Frame Definition

完成 涛 陆

10:42 功能 #2594: Ford_SYSR：FS_REQ0073_V1 Node Lighting Module Configuration Mechanics

完成 涛 陆

10:41 功能 #2593: Ford_SYSR：FS_REQ0072_V1 Node Lighting Module Configuration

完成 涛 陆

10:38 功能 #2593: Ford_SYSR：FS_REQ0072_V1 Node Lighting Module Configuration

完成 涛 陆

10:36 功能 #2592: Ford_SYSR：FS_REQ0071_V1 Description of Node Reporting

完成 涛 陆

10:31 功能 #2591: Ford_SYSR：FS_REQ0070_V2 BCM EEL VO Load Sequencing

部分完成，PWM信号未接入 涛 陆

10:30 功能 #2585: Ford_SYSR：FS_REQ0064_V1 EEL LIN Message Sequencing

报文发送时序是定义在LDF里的,软件只需LIN通讯正常即可证明满足该需求. 盛炜 朱

10:20 功能 #2585: Ford_SYSR：FS_REQ0064_V1 EEL LIN Message Sequencing

与软件无关，上位机需求 涛 陆

10:26 功能 #2590: Ford_SYSR：FS_REQ0069_V1 BCM EEL LDM Node Status Report Frame

大部分完成 涛 陆

10:24 功能 #2589: Ford_SYSR：FS_REQ0068_V1 Exterior Lighting Functional Support

未完成，有些信号没有获取 涛 陆

10:22 功能 #2588: Ford_SYSR：FS_REQ0067_V1 BCM EEL Command Frame 2

完成 涛 陆

10:22 功能 #2587: Ford_SYSR：FS_REQ0066_V1 BCM EEL Command Frame 1

完成 涛 陆

10:21 功能 #2586: Ford_SYSR：FS_REQ0065_V1 EEL LIN Identifier Allocation

完成 涛 陆

10:19 功能 #2584: Ford_SYSR：FS_REQ0063_V2 LDF

完成 涛 陆

10:18 功能 #2583: Ford_SYSR：FS_REQ0062_V2 LDM diagnostic with test command

未完成 涛 陆

10:14 功能 #2582: Ford_SYSR：FS_REQ0061_V3 Failure Recover strategy

LDM receives 3 valid LIN signals within 500 ms未完成 涛 陆

10:12 功能 #2581: Ford_SYSR：FS_REQ006x_V2 LB Activation Redundant

未完成 涛 陆

10:10 功能 #2580: Ford_SYSR：FS_REQ0060_V1 LIN Bus Failures

未完成 涛 陆

10:10 功能 #2579: Ford_SYSR：FS_REQ0059_V1 LIN Lost

未完成 涛 陆

10:08 功能 #2578: Ford_SYSR：FS_REQ0058_V1 NTC Thermistor Failure

完成 涛 陆

10:08 功能 #2577: Ford_SYSR：FS_REQ0057_V1 Binning Resistor Lost or Out of Range

完成 涛 陆

10:07 功能 #2576: Ford_SYSR：FS_REQ0056_V1 Buck Failure Detection

完成 涛 陆

10:07 功能 #2575: Ford_SYSR：FS_REQ0055_V3 LDM Failure Response Reporting

完成 涛 陆

10:06 功能 #2573: Ford_SYSR：FS_REQ0053_V2 General LED Failure Detection

完成 涛 陆

10:05 功能 #2572: Ford_SYSR：FS_REQ0052_V1_LED Thermal Derating Smooth Appearance

曲线有问题，需要修改 涛 陆

10:04 功能 #2571: Ford_SYSR：FS_REQ0051_V1 NTC Calculation

完成 涛 陆

10:04 功能 #2570: Ford_SYSR：FS_REQ0050_V2 LDM intermal Thermal Derating

涛 陆 在 #note-1 中写到：
> 按照DV mode给的曲线开发的，未按照FS开发
SBL部分未开发 涛 陆

10:02 功能 #2570: Ford_SYSR：FS_REQ0050_V2 LDM intermal Thermal Derating

按照DV mode给的曲线开发的，未按照FS开发 涛 陆

10:01 功能 #2569: Ford_SYSR：FS_REQ0049_V2 Output Thermal Derating curve

完成 涛 陆

10:00 功能 #2568: Ford_SYSR：FS_REQ0048_V1 Thermal Monitoring

完成 涛 陆

09:59 功能 #2566: Ford_SYSR：FS_REQ0046_V1 Fan Failure Detection

部分完成 涛 陆

09:58 功能 #2565: Ford_SYSR：FS_REQ0045_V2 Activation of the Fan

完成 涛 陆

09:58 功能 #2564: Ford_SYSR：FS_REQ0044_V1 FAN Functional self-test when power on

未完成 涛 陆

09:57 功能 #2562: Ford_SYSR：FS_REQ0042_V2 Binning Resistor

完成 涛 陆

09:56 功能 #2561: Ford_SYSR：FS_REQ0041_V2 Channel output intensity Smooth Fading

完成 涛 陆

09:55 功能 #2560: Ford_SYSR：FS_REQ0040_V1 Light Source Activation Latency Times

热启动有问题 涛 陆

09:55 功能 #2559: Ford_SYSR：FS_REQ0039_V2 Fading Requirements

未完成 涛 陆

09:53 功能 #2558: Ford_SYSR：FS_REQ0038_V3 Welcome/Farewell Fade Activation Signals

完成 涛 陆

09:53 功能 #2557: Ford_SYSR：FS_REQ0037_V1 PWM channel Welcome/Farewell Activation

未完成 涛 陆

09:52 功能 #2556: Ford_SYSR：FS_REQ0036_V2 DRL Welcome/Farewell Activation

完成 涛 陆

09:52 功能 #2555: Ford_SYSR：FS_REQ0035_V1 Static Bending Light Activation

未完成 涛 陆

09:52 功能 #2554: Ford_SYSR：FS_REQ0034_V1 Side marker Activation

未完成 涛 陆

09:51 功能 #2553: Ford_SYSR：FS_REQ0033_V1 Cornering Activation

未完成 涛 陆

09:49 功能 #2552: Ford_SYSR：FS_REQ0032_V1 Front Fog Activation

未完成 涛 陆

09:49 功能 #2551: Ford_SYSR：FS_REQ0031_V2_Licoln Lit Star Activation

未完成 涛 陆

09:48 功能 #2550: Ford_SYSR：FS_REQ0030_V1 DRL Response to Flash-To-Pass Activation

完成 涛 陆

09:46 功能 #2548: Ford_SYSR：FS_REQ0028_V1 DRL Response to Low Beam outage

完成 涛 陆

09:44 功能 #2547: Ford_SYSR：FS_REQ0027_V1 DRL EEL LIN command Table

完成 涛 陆

09:43 功能 #2546: Ford_SYSR：FS_REQ0026_V2 DRL Control Strategy

完成 涛 陆

09:43 功能 #2545: Ford_SYSR：FS_REQ0025_V3 Turn Indicator Feedback

完成 涛 陆

09:42 功能 #2544: Ford_SYSR：FS_REQ0024_V1 Turn Indicator Delay

未完成 涛 陆

09:42 功能 #2543: Ford_SYSR：FS_REQ0023_V3 Turn Indicator Activation

7V无法采样，其他功能完成 涛 陆

09:39 功能 #2542: Ford_SYSR：FS_REQ0022_V2 High Beam EEL Front Fog Activation Reaction

未完成 涛 陆

09:37 功能 #2541: Ford_SYSR：FS_REQ0021_V1 High Beam EEL LIN Flash-to-Pass Activation

完成 涛 陆

09:36 功能 #2540: Ford_SYSR：FS_REQ0020_V1 High Beam LDM standard ramping

完成 涛 陆

09:36 功能 #2539: Ford_SYSR：FS_REQ0019_V1 High Beam (HB) HCM EEL LIN Activation(Not in LDM4 scope)

完成 涛 陆

09:35 功能 #2538: Ford_SYSR：FS_REQ0018_V1 High Beam (HB) BCM EEL LIN Activation

完成 涛 陆

09:35 功能 #2537: Ford_SYSR：FS_REQ0017_V2 LB Activation

该PIN未IO口，无法采样电压 涛 陆

09:33 功能 #2535: Ford_SYSR：FS_REQ0015_V2 Low Side Driver 1 and 2 usage Configuration

除了SBL，其他功能已完成 涛 陆

09:32 功能 #2534: Ford_SYSR：FS_REQ0014_V1 Low Side Driver 1 and 2 Channel Configuration

未完成 涛 陆

09:31 功能 #2533: Ford_SYSR：FS_REQ0013_V1 Channel 2 to 4 Functional Configuration

完成 涛 陆

09:31 功能 #2532: Ford_SYSR：FS_REQ0012_V1 DRL Failsafe Mode

需求取消，该硬线改为信号线 涛 陆

09:30 功能 #2531: Ford_SYSR：FS_REQ0011_V3 Turn Indicator Failsafe Mode

完成 涛 陆

09:29 功能 #2530: Ford_SYSR：FS_REQ0010_V1 Channel 1 Failsafe Mode

部分完成
以下列表已完成
> |Function |Failsafe Requirement|
> |LB Light Output |Required|
> |LB Thermal Derating |Required|
... 涛 陆

09:28 功能 #2519: Ford_SYSR: System Requirement

完成 涛 陆

09:27 功能 #2528: Ford_SYSR：FS_REQ0008_V1 Side Detection

完成 涛 陆

09:27 功能 #2527: Ford_SYSR：FS_REQ0007_V1 TI Power Mode

完成 涛 陆

09:27 功能 #2526: Ford_SYSR：FS_REQ0006_V1 DRL/PO Power supply

完成 涛 陆

09:26 功能 #2525: Ford_SYSR：FS_REQ0005_V1 Channel 2(Main) Power Mode

与软件无关 涛 陆

2024-10-24

20:19 功能 #2607 (已关闭): Ford_SYSR：FS_REQ0086_V1 LDM Factory Mode

To protect headlamp damage from over/unexpected current of default LDM Dataset configuration in Tier1 plant or other ... 玉洁 金

20:17 功能 #2606 (进行中): Ford_SYSR：FS_REQ0085_V1 Ford Functional Safety

The LDM shall meet the functional safety requirements for each of following ASIL rated features:
|_.Item ID|_.Item n... 玉洁 金

20:14 功能 #2605 (已关闭): Ford_SYSR：FS_REQ0084_V2 Software Flashing

The LDM SW and parameters shall be flashable via Lin bus acc. to ‘SWDL 00.06.15.002-006’. Please consider that the LI... 玉洁 金

20:14 功能 #2604 (已关闭): Ford_SYSR：FS_REQ0083_V1 MSB vs. LSB

In some LIN frames the message is distributed over more than one byte. In every case the frame shall be read as the f... 玉洁 金

20:13 功能 #2603 (已关闭): Ford_SYSR：FS_REQ0082_V1 Supplier Defined: Service Return and Development Reporting

For supplier use in development of the LDM and for analysis of warranty service return parts, the supplier should imp... 玉洁 金

20:12 功能 #2602 (已关闭): Ford_SYSR：FS_REQ0081_V1 Supplier Defined: Lamp Manufacturing

LDM needs to support Dataset flashing on Ford Manufacturing. 玉洁 金

20:11 功能 #2601 (新建): Ford_SYSR：FS_REQ0080_V2 LDM Self-Test Description

In the case a “cycle all” is requested the LDM shall illuminate the following outputs in 3 seconds with the following... 玉洁 金

20:10 功能 #2600 (新建): Ford_SYSR：FS_REQ0079_V2 Self-Test Frame

This diagnostic LF/RF_EEL_LoadTest frame includes a cycle all load test. This test allows the definition of an activa... 玉洁 金

20:09 功能 #2599 (已关闭): Ford_SYSR：FS_REQ0078_V1 LIN Part Number Reporting

Since we are limited to only 7 bytes of data (besides the LIN Status Byte), transmitting a 23 character part number w... 玉洁 金

19:58 功能 #2598 (已关闭): Ford_SYSR：FS_REQ0077_V3 Run Time Configuration Validation

The Front LDM modules will check the configuration data index to that broadcast by the BCM. BCM Command Frame 2 conta... 玉洁 金

19:57 功能 #2597 (已关闭): Ford_SYSR：FS_REQ0076_V1 LDM Configuration Monitoring

-The LF_EEL and RF_EEL will support monitoring of BCM Configuration and confirm it matches the vehicle programmed val... 玉洁 金

19:56 功能 #2596 (已关闭): Ford_SYSR：FS_REQ0075_V1 Configuration Support

BCM will support configuration of the LIN nodes using the established methods for configuration that are already in p... 玉洁 金

19:56 功能 #2595 (已关闭): Ford_SYSR：FS_REQ0074_V2 LIN Configuration Frame Definition

!clipboard-202411011314-1kq8r.png!
Table 40: BCM Front EEL Configuration Frame
!clipboard-202411011315-4n6yy.png!
... 玉洁 金

19:55 功能 #2594 (已关闭): Ford_SYSR：FS_REQ0073_V1 Node Lighting Module Configuration Mechanics

Configuring a LIN Node is not a download. It uses a functional message to transfer data one time to the LIN node. The... 玉洁 金

19:44 功能 #2593 (已关闭): Ford_SYSR：FS_REQ0072_V1 Node Lighting Module Configuration

Configuration of the LIN Nodes can be accomplished through multiple mechanisms, in vehicle or subassembly electrical ... 玉洁 金

19:44 功能 #2592 (已关闭): Ford_SYSR：FS_REQ0071_V1 Description of Node Reporting

SAE J2602 Status Byte
In J2602, the very first byte transmitted by any node is the LIN Status Byte. It has this form... 玉洁 金

19:37 功能 #2591 (新建): Ford_SYSR：FS_REQ0070_V2 BCM EEL VO Load Sequencing

The following command message is used to actuate each load individually. The LDM shall only consider LF EEL and RF EE... 玉洁 金

19:35 功能 #2590 (已关闭): Ford_SYSR：FS_REQ0069_V1 BCM EEL LDM Node Status Report Frame

The following frame describes the signals being reported by the LDM
• Name: Node Status Message
• Size: 8 Byte
• T... 玉洁 金

19:32 功能 #2589 (已关闭): Ford_SYSR：FS_REQ0068_V1 Exterior Lighting Functional Support

Many of the signals defined in the Command Frames provide functionality that appear to overlap and do to some extent.... 玉洁 金

19:24 功能 #2588 (已关闭): Ford_SYSR：FS_REQ0067_V1 BCM EEL Command Frame 2

The following is the second frame from the BCM providing commands and state information used by the LDM.

o Name:... 玉洁 金

19:20 功能 #2587 (已关闭): Ford_SYSR：FS_REQ0066_V1 BCM EEL Command Frame 1

The following is the first frame from the BCM providing commands and state information used by the LDM.

o Name: ... 玉洁 金

19:19 功能 #2586 (已关闭): Ford_SYSR：FS_REQ0065_V1 EEL LIN Identifier Allocation

The following tables list the address assignments, the message publisher and target recipient for the message data. ... 玉洁 金

19:16 功能 #2585 (已关闭): Ford_SYSR：FS_REQ0064_V1 EEL LIN Message Sequencing

The following diagram illustrates the LIN messaging sequence for the BCM EEL LIN Bus. The BCM will alternate between ... 玉洁 金

19:16 功能 #2584 (已关闭): Ford_SYSR：FS_REQ0063_V2 LDF

The LDM shall consider LDF BCM_G2_LIN_05_Ckt_v17_2016Dec01.LDF when on BCM LIN (10,417 baud).
!clipboard-20241024191... 玉洁 金

19:14 功能 #2583 (已关闭): Ford_SYSR：FS_REQ0062_V2 LDM diagnostic with test command

LDM shall support diagnostic capability to read the configuration and fault status with specific engineering diagnost... 玉洁 金

19:13 功能 #2582 (已关闭): Ford_SYSR：FS_REQ0061_V3 Failure Recover strategy

All the LDM failure above in this chapter shall recovery when:
• LED load returns to normal operation(N-x except, N-... 玉洁 金

19:11 功能 #2581: Ford_SYSR：FS_REQ006x_V2 LB Activation Redundant

To enhance the LB fault handling capability under FUSA TSR 1.4.2 requirement, currently LB hardwire is used as activa... 玉洁 金

19:05 功能 #2581 (已关闭): Ford_SYSR：FS_REQ006x_V2 LB Activation Redundant

To enhance the LB fault handling capability under FUSA TSR 1.4.2 requirement, to adopt LB hardwire or LIN signal “Hea... 玉洁 金

19:02 功能 #2580 (已关闭): Ford_SYSR：FS_REQ0060_V1 LIN Bus Failures

The Network shall meet the requirements as defined per the following failure modes:
• LDM Power Loss – LDM shall not... 玉洁 金

19:01 功能 #2579 (已关闭): Ford_SYSR：FS_REQ0059_V1 LIN Lost

In case of “LIN lost”, the LDM shall continue functioning. A “LIN lost” situation occurs if:
• 5000 mS (+/- 50mS) no... 玉洁 金

18:59 功能 #2578 (已关闭): Ford_SYSR：FS_REQ0058_V1 NTC Thermistor Failure

If the NTC resistor is lost or its value out is of range(<-40°C || >150°C), then corresponding channels shall be driv... 玉洁 金

18:58 功能 #2577 (已关闭): Ford_SYSR：FS_REQ0057_V1 Binning Resistor Lost or Out of Range

If the binning resistor is lost (short circuit or open circuit) or out of range, it shall not cause overcurrent excee... 玉洁 金

18:57 功能 #2576 (已关闭): Ford_SYSR：FS_REQ0056_V1 Buck Failure Detection

The failures that the buck itself detects are the followings:
o Short to GND
o Short to battery in HSD when it i... 玉洁 金

18:57 功能 #2575 (已关闭): Ford_SYSR：FS_REQ0055_V3 LDM Failure Response Reporting

If failure occurs, the LED voltage, LDM temperature and failure time shall be saved and reported. The last five error... 玉洁 金

18:56 功能 #2574 (已关闭): Ford_SYSR：FS_REQ0054_V1 Load Failure Response Deactivation

LED outage detection shall work within -40 to 110°C ambient temperature range. Input voltage range for LED outage det... 玉洁 金

18:55 功能 #2573 (已关闭): Ford_SYSR：FS_REQ0053_V2 General LED Failure Detection

The LDM must support outage detection on all output channels. Outage detection will only occur while the channel is o... 玉洁 金

18:54 功能 #2572 (已关闭): Ford_SYSR：FS_REQ0052_V1_LED Thermal Derating Smooth Appearance

The LDM shall thermal dim at a rate no greater than 2.5%/sec for thermal derating purposes to provide a smooth lighti... 玉洁 金

18:53 功能 #2571 (已关闭): Ford_SYSR：FS_REQ0051_V1 NTC Calculation

Selection of the NTC is the responsibility of the headlamp supplier. The LDM shall be capable of supporting a wide va... 玉洁 金

18:51 功能 #2570 (已关闭): Ford_SYSR：FS_REQ0050_V2 LDM intermal Thermal Derating

The LDM shall have an internal NTC thermistor and monitor temperatures critical to operation. To avoid stressing the ... 玉洁 金

18:47 功能 #2569 (已关闭): Ford_SYSR：FS_REQ0049_V2 Output Thermal Derating curve

All output functions shall have a defined derating curves using 5 points described by a temperature and a percent der... 玉洁 金

18:46 功能 #2568 (已关闭): Ford_SYSR：FS_REQ0048_V1 Thermal Monitoring

The LDM must monitor the headlamp PCBA temperatures with NTC thermistors to thermally derate LED functions current to... 玉洁 金

18:45 功能 #2567 (已关闭): Ford_SYSR：FS_REQ0047_V1 LED Thermal Derating

The LDM shall control the LED junction temperature by controlling the current to the LED via peak current derating. I... 玉洁 金

18:43 功能 #2566 (已关闭): Ford_SYSR：FS_REQ0046_V1 Fan Failure Detection

According to the content of the configuration parameter ‘Fan_Outage_Detect_cfg’, the LDM will either perform full sta... 玉洁 金

18:41 功能 #2565 (已关闭): Ford_SYSR：FS_REQ0045_V2 Activation of the Fan

The activation of FAN can be configured by the parameter ‘FAN_Activation_Trigger_cfg’.
• 0x00: No FAN
• 0x01:Activa... 玉洁 金

18:40 功能 #2564 (已关闭): Ford_SYSR：FS_REQ0044_V1 FAN Functional self-test when power on

After power on of the LDM, the fan will be activated for specific amount of time to do the functional test.The time c... 玉洁 金

18:40 功能 #2563 (已关闭): Ford_SYSR：FS_REQ0043_V2 Bin Class Current Setting

BIN current can be set for BIN0 to BIN7 of each channel in the configuration parameter file, the current range should... 玉洁 金

18:38 功能 #2562 (已关闭): Ford_SYSR：FS_REQ0042_V2 Binning Resistor

The LDM shall be capable of supporting a binning resistor input for each channel to set the current for the correspon... 玉洁 金

18:35 功能 #2561 (已关闭): Ford_SYSR：FS_REQ0041_V2 Channel output intensity Smooth Fading

No ramping is required between 0 and 5%, 8 bit resolution is required. A non-linear ramp per Steven’s Power Law shall... 玉洁 金

18:33 功能 #2560 (已关闭): Ford_SYSR：FS_REQ0040_V1 Light Source Activation Latency Times

The LDM shall be capable of activating each function within the times provided below. Latency time refers to activati... 玉洁 金

18:30 功能 #2559 (已关闭): Ford_SYSR：FS_REQ0039_V2 Fading Requirements

| |Channel 1 |Channel 2 |Channel 3 |Channel 4 |LSD1&2|
|Fade-in capability from 0% onwards |Yes |Yes |Yes |Yes... 玉洁 金

18:27 功能 #2558 (已关闭): Ford_SYSR：FS_REQ0038_V3 Welcome/Farewell Fade Activation Signals

The Welcome/Farewell activation shall be triggered by the LIN command ‘WFSubstate’ in both ‘BCM_E_FC1’ and‘BCM_E_FC2’... 玉洁 金

18:24 功能 #2557 (已关闭): Ford_SYSR：FS_REQ0037_V1 PWM channel Welcome/Farewell Activation

PWM channels shall be also capable to be used during Welcome/Farewell sequence, according to above ‘PWMx_Function_Ass... 玉洁 金

18:23 功能 #2556 (已关闭): Ford_SYSR：FS_REQ0036_V2 DRL Welcome/Farewell Activation

When the LDM is triggered to fade on for embrace, the LDM shall fade from 0% to the duty cycle given by ‘DRL_Embrace_... 玉洁 金

18:22 功能 #2555 (已关闭): Ford_SYSR：FS_REQ0035_V1 Static Bending Light Activation

The static bending light (SBL) will be activated based on steering wheel angle provided by the Signal ‘SteAngle’ and ... 玉洁 金

18:22 功能 #2554 (已关闭): Ford_SYSR：FS_REQ0034_V1 Side marker Activation

The activation/deactivation of side marker light shall be triggered by BCM LIN command ‘Position_Park_Left/Right_Cmd’... 玉洁 金

18:21 功能 #2553 (已关闭): Ford_SYSR：FS_REQ0033_V1 Cornering Activation

The activation/deactivation of cornering light shall be triggered by BCM LIN command ‘Cornering_cmd’ with the LDM sid... 玉洁 金

18:20 功能 #2552 (已关闭): Ford_SYSR：FS_REQ0032_V1 Front Fog Activation

The activation/deactivation of front fog light shall be triggered by BCM LIN command ‘Front_Fog_Request’.
‘Front_F... 玉洁 金

18:20 功能 #2551 (已关闭): Ford_SYSR：FS_REQ0031_V2_Licoln Lit Star Activation

The activation/deactivation of Licoln Star shall be triggered by BCM LIN command ‘Position_Park_Left/Right_Cmd’ with ... 玉洁 金

18:19 功能 #2550 (已关闭): Ford_SYSR：FS_REQ0030_V1 DRL Response to Flash-To-Pass Activation

If the DRL is active, and flash to pass signal is received via LIN and IGN is either run or start, the LDM shall foll... 玉洁 金

18:06 功能 #2548 (已关闭): Ford_SYSR：FS_REQ0028_V1 DRL Response to Low Beam outage

DRL maybe affected by LB if LB outage is detected and configured to be turned off, a configurable parameter “DRL_LB_O... 玉洁 金

18:06 功能 #2547 (已关闭): Ford_SYSR：FS_REQ0027_V1 DRL EEL LIN command Table

The output of the dedicated LIN controlled DRL/Position function shall be determined based on the following LIN signa... 玉洁 金

18:03 功能 #2546 (已关闭): Ford_SYSR：FS_REQ0026_V2 DRL Control Strategy

The module will be capable of determining DRL state by either BCM LIN or by BCM ‘L/RF_DRL_LAMP_Ckt’ direct wire.
... 玉洁 金

18:02 功能 #2545 (已关闭): Ford_SYSR：FS_REQ0025_V3 Turn Indicator Feedback

Under normal operating conditions, the LDM shall report Turn indicator status to the BCM by outputting the received s... 玉洁 金

18:01 功能 #2544 (已关闭): Ford_SYSR：FS_REQ0024_V1 Turn Indicator Delay

The LDM shall support a configurable delay time of the turn indicator to be able to synchronize with other turn indic... 玉洁 金

18:01 功能 #2543 (已关闭): Ford_SYSR：FS_REQ0023_V3 Turn Indicator Activation

For the definition of the operational state of the Turn Indicator, the voltage level of the Turn supply terminal of t... 玉洁 金

17:59 功能 #2542 (已关闭): Ford_SYSR：FS_REQ0022_V2 High Beam EEL Front Fog Activation Reaction

The parameter ‘HB_combined_Front_fog_cfg’ describes the handling of HB deactivation in case of front fog activation. ... 玉洁 金

17:58 功能 #2541 (已关闭): Ford_SYSR：FS_REQ0021_V1 High Beam EEL LIN Flash-to-Pass Activation

In the event the LIN signal ‘FTP_Status’ transitions from ‘0’ to ‘1’, the high beam output(s) shall activate immediat... 玉洁 金

17:57 错误 #2515 (已解决): 需求确认

盛炜 朱

17:56 错误 #2515: 需求确认

!
!clipboard-202410241756-fie2e.png!
! 盛炜 朱

14:17 错误 #2515 (已关闭): 需求确认

当我配置LB_ Failure_Report_cfg/HB_ Failure_Report_cfg/DRL_ Failure_Report_cfg都为disable的时候，APINF2和APINFO3是否都需要置一，现在有个这个问题，... 传鹏 胡

17:57 功能 #2540 (已关闭): Ford_SYSR：FS_REQ0020_V1 High Beam LDM standard ramping

The LDM shall also have the option to select a standard LDM ramping time within parameters. To do this the parameter ... 玉洁 金

17:56 功能 #2539 (已关闭): Ford_SYSR：FS_REQ0019_V1 High Beam (HB) HCM EEL LIN Activation(Not in LDM4 scope)

In FNV2 HCM configuration the corresponding HCM HB commands will also activate the HB and/or HB2 as requested by ‘LDM... 玉洁 金

17:55 功能 #2538 (已关闭): Ford_SYSR：FS_REQ0018_V1 High Beam (HB) BCM EEL LIN Activation

High beam (of any type) shall only activate if IGN is in Run or Start.
The high beam function shall be capable of ... 玉洁 金

17:54 功能 #2537 (已关闭): Ford_SYSR：FS_REQ0017_V2 LB Activation

For the definition of the operational state of the LB, the voltage level of the LB supply terminal of the BCM (‘L/RF_... 玉洁 金

17:54 功能 #2536 (已关闭): Ford_SYSR：FS_REQ0016_V3 PWM output configuration

The LDM shall have 4 PWM outputs capable of controlling any of the following functions via configure parameter ‘PWMx_... 玉洁 金

17:53 功能 #2535 (已关闭): Ford_SYSR：FS_REQ0015_V2 Low Side Driver 1 and 2 usage Configuration

The function of the Low Side driver shall also be configurable. The low side driver activation shall then be based o... 玉洁 金

17:51 功能 #2534 (已关闭): Ford_SYSR：FS_REQ0014_V1 Low Side Driver 1 and 2 Channel Configuration

Additional secondary functions may be added any of the 4 channels (including channel 1) using one of the 2 low side d... 玉洁 金

17:49 功能 #2533 (已关闭): Ford_SYSR：FS_REQ0013_V1 Channel 2 to 4 Functional Configuration

Channel 2 to 4 shall be capable of supporting the following functions based on the parameters “Channel2/3/4_usage_cfg... 玉洁 金

17:48 功能 #2532 (已关闭): Ford_SYSR：FS_REQ0012_V1 DRL Failsafe Mode

The input will be active in BCM failsafe mode, and only under DRL hardwire control condition, the DRL and all corresp... 玉洁 金

17:45 功能 #2531 (已关闭): Ford_SYSR：FS_REQ0011_V3 Turn Indicator Failsafe Mode

The input will be active in BCM failsafe mode, and therefore the TI and all corresponding main functions of the TI sh... 玉洁 金

17:43 功能 #2530 (已关闭): Ford_SYSR：FS_REQ0010_V1 Channel 1 Failsafe Mode

The channel1 input will be active in BCM failsafe mode, and LB and all corresponding main functions of the LB shall b... 玉洁 金

17:39 功能 #2529 (已关闭): Ford_SYSR：FS_REQ0009_V1 Channel 1 output Assignment

The high side assignment of channel 1 must be base low beam in all cases. This shall not be configurable via LDM para... 玉洁 金

17:38 功能 #2528 (已关闭): Ford_SYSR：FS_REQ0008_V1 Side Detection

The LDMs will be used on a single LIN bus and needs to have defined mounting position information. To keep the LDM pa... 玉洁 金

17:30 功能 #2527 (已关闭): Ford_SYSR：FS_REQ0007_V1 TI Power Mode

Power for Turn indicator prefer to be apply to the “Power Supply Channel 3” input.
In the case channel 3 is sourced... 玉洁 金

17:29 功能 #2526 (已关闭): Ford_SYSR：FS_REQ0006_V1 DRL/PO Power supply

DRL/PO input can be supplied with two different modes:
1) a PWM signal from BCM direct wire ‘L/RF_DRL_LAMP_Ckt’ to p... 玉洁 金

17:28 功能 #2525 (已关闭): Ford_SYSR：FS_REQ0005_V1 Channel 2(Main) Power Mode

Channel 2 input (Main Power Feed) will be supplied with a steady state power supply from the vehicle to be considered... 玉洁 金

17:26 功能 #2524 (已关闭): Ford_SYSR：FS_REQ0004_V1 Channel 1 Power Mode

The LDM Channel 1 output shall be triggered by BCM Low Beam Circuit(L/RF_Low_Beam_Ckt) as described in Figure 3.
A... 玉洁 金

17:24 功能 #2523 (已关闭): Ford_SYSR：FS_REQ0003_V2 Channel power source Configuration

|Channel No. |Channelx_ Power_Source_cfg|
|Channel 1 |BCM LB (L/RF-Low_Beam_Ckt)|
|Channel 2 |Relay connected to... 玉洁 金

17:03 功能 #2522 (已关闭): Ford_SYSR：FS_REQ0002_V1 LDM Input Transients

The LDM will be expected to withstand input transients described by:
• FMC1278 - Electromagnetic Compatibility Spec... 玉洁 金

16:03 功能 #2520 (已关闭): Ford_SYSR: FS_REQ0001_V2 LDM Input

The LDM will use Channel2 as main power input as HS REQ005, and rest channels input to be used as an input signal to ... 斌 徐

15:58 功能 #2519 (已关闭): Ford_SYSR: System Requirement

-FS_LDM Localization_V2.0.docx-
FS_LDM Localization_V2.6.docx
HS_LDM Localization_V2.2.docx 斌 徐

14:54 Task #2516 (已关闭): Ford_SWET: Static code analysis

Application software Static code analysis(S00071691.7) 斌 徐

2024-10-23

16:53 Bug #2514 (Bug-已关闭): HB呼吸问题

HB的Fade speed配置为slow（4000ms），实际没有4000ms 传鹏 胡

16:11 Bug #2513 (Bug-问题回归验证): 单元测试测试问题反馈

1.app_dpl 代码最后存在PWM重复赋值计算，需删除
2.app_fan fan状态为error时，fan赋值错误，未停止fan，需分析修改 槐 杨

16:04 Task #2509: Ford_SWET: DV&PV Software Test

完成A001.6版本单元测试，静态测试，LIN一致性测试及报告更新
等待A001.8版本发布 槐 杨

15:59 Bug #2512 (Bug-已关闭): 工厂模式在有app，boot和dataset的时候，刷app后，dataset会被冲掉变成空白

在工厂模式下，有BOOT，APP,dataset的时候，再次刷写APP，原先的dataset会被冲掉，在读dataset的版本会变成空白 传鹏 胡

15:49 Bug #2511 (Bug-已关闭): 退出低功耗模式无法正常点灯

电源上电，不给任何逻辑，进入低功耗，在上任意逻辑，对应功能点不亮 传鹏 胡

2024-10-22

10:30 Task #2510 (进行中): Ford_Fusa: function Safety SSR

Complete and sign Fusa SSR documents with Ford team 斌 徐

10:28 Task #2509 (已关闭): Ford_SWET: DV&PV Software Test

Ford LDM Function Test 斌 徐

10:26 Task #2508 (已关闭): Ford_SWED: DV&PV Software Release

Release Software for DV/PV test:
Boot loader Software Version：SW0007170.B001
Application Software Version：SW0007169... 斌 徐