项目

一般

简介

活动

从 2024-10-15 到 2024-10-24

2024-10-24

20:19 功能 #2607 (已关闭): Ford_SYSR：FS_REQ0086_V1 LDM Factory Mode
To protect headlamp damage from over/unexpected current of default LDM Dataset configuration in Tier1 plant or other ... 玉洁 金
20:17 功能 #2606 (进行中): Ford_SYSR：FS_REQ0085_V1 Ford Functional Safety
The LDM shall meet the functional safety requirements for each of following ASIL rated features:
|_.Item ID|_.Item n... 玉洁 金
20:14 功能 #2605 (已关闭): Ford_SYSR：FS_REQ0084_V2 Software Flashing
The LDM SW and parameters shall be flashable via Lin bus acc. to ‘SWDL 00.06.15.002-006’. Please consider that the LI... 玉洁 金
20:14 功能 #2604 (已关闭): Ford_SYSR：FS_REQ0083_V1 MSB vs. LSB
In some LIN frames the message is distributed over more than one byte. In every case the frame shall be read as the f... 玉洁 金
20:13 功能 #2603 (已关闭): Ford_SYSR：FS_REQ0082_V1 Supplier Defined: Service Return and Development Reporting
For supplier use in development of the LDM and for analysis of warranty service return parts, the supplier should imp... 玉洁 金
20:12 功能 #2602 (已关闭): Ford_SYSR：FS_REQ0081_V1 Supplier Defined: Lamp Manufacturing
LDM needs to support Dataset flashing on Ford Manufacturing. 玉洁 金
20:11 功能 #2601 (新建): Ford_SYSR：FS_REQ0080_V2 LDM Self-Test Description
In the case a “cycle all” is requested the LDM shall illuminate the following outputs in 3 seconds with the following... 玉洁 金
20:10 功能 #2600 (新建): Ford_SYSR：FS_REQ0079_V2 Self-Test Frame
This diagnostic LF/RF_EEL_LoadTest frame includes a cycle all load test. This test allows the definition of an activa... 玉洁 金
20:09 功能 #2599 (已关闭): Ford_SYSR：FS_REQ0078_V1 LIN Part Number Reporting
Since we are limited to only 7 bytes of data (besides the LIN Status Byte), transmitting a 23 character part number w... 玉洁 金
19:58 功能 #2598 (已关闭): Ford_SYSR：FS_REQ0077_V3 Run Time Configuration Validation
The Front LDM modules will check the configuration data index to that broadcast by the BCM. BCM Command Frame 2 conta... 玉洁 金
19:57 功能 #2597 (已关闭): Ford_SYSR：FS_REQ0076_V1 LDM Configuration Monitoring
-The LF_EEL and RF_EEL will support monitoring of BCM Configuration and confirm it matches the vehicle programmed val... 玉洁 金
19:56 功能 #2596 (已关闭): Ford_SYSR：FS_REQ0075_V1 Configuration Support
BCM will support configuration of the LIN nodes using the established methods for configuration that are already in p... 玉洁 金
19:56 功能 #2595 (已关闭): Ford_SYSR：FS_REQ0074_V2 LIN Configuration Frame Definition
!clipboard-202411011314-1kq8r.png!
Table 40: BCM Front EEL Configuration Frame
!clipboard-202411011315-4n6yy.png!
... 玉洁 金
19:55 功能 #2594 (已关闭): Ford_SYSR：FS_REQ0073_V1 Node Lighting Module Configuration Mechanics
Configuring a LIN Node is not a download. It uses a functional message to transfer data one time to the LIN node. The... 玉洁 金
19:44 功能 #2593 (已关闭): Ford_SYSR：FS_REQ0072_V1 Node Lighting Module Configuration
Configuration of the LIN Nodes can be accomplished through multiple mechanisms, in vehicle or subassembly electrical ... 玉洁 金
19:44 功能 #2592 (已关闭): Ford_SYSR：FS_REQ0071_V1 Description of Node Reporting
SAE J2602 Status Byte
In J2602, the very first byte transmitted by any node is the LIN Status Byte. It has this form... 玉洁 金
19:37 功能 #2591 (新建): Ford_SYSR：FS_REQ0070_V2 BCM EEL VO Load Sequencing
The following command message is used to actuate each load individually. The LDM shall only consider LF EEL and RF EE... 玉洁 金
19:35 功能 #2590 (已关闭): Ford_SYSR：FS_REQ0069_V1 BCM EEL LDM Node Status Report Frame
The following frame describes the signals being reported by the LDM
• Name: Node Status Message
• Size: 8 Byte
• T... 玉洁 金
19:32 功能 #2589 (已关闭): Ford_SYSR：FS_REQ0068_V1 Exterior Lighting Functional Support
Many of the signals defined in the Command Frames provide functionality that appear to overlap and do to some extent.... 玉洁 金
19:24 功能 #2588 (已关闭): Ford_SYSR：FS_REQ0067_V1 BCM EEL Command Frame 2
The following is the second frame from the BCM providing commands and state information used by the LDM.

o Name:... 玉洁 金
19:20 功能 #2587 (已关闭): Ford_SYSR：FS_REQ0066_V1 BCM EEL Command Frame 1
The following is the first frame from the BCM providing commands and state information used by the LDM.

o Name: ... 玉洁 金
19:19 功能 #2586 (已关闭): Ford_SYSR：FS_REQ0065_V1 EEL LIN Identifier Allocation
The following tables list the address assignments, the message publisher and target recipient for the message data. ... 玉洁 金
19:16 功能 #2585 (已关闭): Ford_SYSR：FS_REQ0064_V1 EEL LIN Message Sequencing
The following diagram illustrates the LIN messaging sequence for the BCM EEL LIN Bus. The BCM will alternate between ... 玉洁 金
19:16 功能 #2584 (已关闭): Ford_SYSR：FS_REQ0063_V2 LDF
The LDM shall consider LDF BCM_G2_LIN_05_Ckt_v17_2016Dec01.LDF when on BCM LIN (10,417 baud).
!clipboard-20241024191... 玉洁 金
19:14 功能 #2583 (已关闭): Ford_SYSR：FS_REQ0062_V2 LDM diagnostic with test command
LDM shall support diagnostic capability to read the configuration and fault status with specific engineering diagnost... 玉洁 金
19:13 功能 #2582 (已关闭): Ford_SYSR：FS_REQ0061_V3 Failure Recover strategy
All the LDM failure above in this chapter shall recovery when:
• LED load returns to normal operation(N-x except, N-... 玉洁 金
19:11 功能 #2581: Ford_SYSR：FS_REQ006x_V2 LB Activation Redundant
To enhance the LB fault handling capability under FUSA TSR 1.4.2 requirement, currently LB hardwire is used as activa... 玉洁 金
19:05 功能 #2581 (已关闭): Ford_SYSR：FS_REQ006x_V2 LB Activation Redundant
To enhance the LB fault handling capability under FUSA TSR 1.4.2 requirement, to adopt LB hardwire or LIN signal “Hea... 玉洁 金
19:02 功能 #2580 (已关闭): Ford_SYSR：FS_REQ0060_V1 LIN Bus Failures
The Network shall meet the requirements as defined per the following failure modes:
• LDM Power Loss – LDM shall not... 玉洁 金
19:01 功能 #2579 (已关闭): Ford_SYSR：FS_REQ0059_V1 LIN Lost
In case of “LIN lost”, the LDM shall continue functioning. A “LIN lost” situation occurs if:
• 5000 mS (+/- 50mS) no... 玉洁 金
18:59 功能 #2578 (已关闭): Ford_SYSR：FS_REQ0058_V1 NTC Thermistor Failure
If the NTC resistor is lost or its value out is of range(<-40°C || >150°C), then corresponding channels shall be driv... 玉洁 金
18:58 功能 #2577 (已关闭): Ford_SYSR：FS_REQ0057_V1 Binning Resistor Lost or Out of Range
If the binning resistor is lost (short circuit or open circuit) or out of range, it shall not cause overcurrent excee... 玉洁 金
18:57 功能 #2576 (已关闭): Ford_SYSR：FS_REQ0056_V1 Buck Failure Detection
The failures that the buck itself detects are the followings:
o Short to GND
o Short to battery in HSD when it i... 玉洁 金
18:57 功能 #2575 (已关闭): Ford_SYSR：FS_REQ0055_V3 LDM Failure Response Reporting
If failure occurs, the LED voltage, LDM temperature and failure time shall be saved and reported. The last five error... 玉洁 金
18:56 功能 #2574 (已关闭): Ford_SYSR：FS_REQ0054_V1 Load Failure Response Deactivation
LED outage detection shall work within -40 to 110°C ambient temperature range. Input voltage range for LED outage det... 玉洁 金
18:55 功能 #2573 (已关闭): Ford_SYSR：FS_REQ0053_V2 General LED Failure Detection
The LDM must support outage detection on all output channels. Outage detection will only occur while the channel is o... 玉洁 金
18:54 功能 #2572 (已关闭): Ford_SYSR：FS_REQ0052_V1_LED Thermal Derating Smooth Appearance
The LDM shall thermal dim at a rate no greater than 2.5%/sec for thermal derating purposes to provide a smooth lighti... 玉洁 金
18:53 功能 #2571 (已关闭): Ford_SYSR：FS_REQ0051_V1 NTC Calculation
Selection of the NTC is the responsibility of the headlamp supplier. The LDM shall be capable of supporting a wide va... 玉洁 金
18:51 功能 #2570 (已关闭): Ford_SYSR：FS_REQ0050_V2 LDM intermal Thermal Derating
The LDM shall have an internal NTC thermistor and monitor temperatures critical to operation. To avoid stressing the ... 玉洁 金
18:47 功能 #2569 (已关闭): Ford_SYSR：FS_REQ0049_V2 Output Thermal Derating curve
All output functions shall have a defined derating curves using 5 points described by a temperature and a percent der... 玉洁 金
18:46 功能 #2568 (已关闭): Ford_SYSR：FS_REQ0048_V1 Thermal Monitoring
The LDM must monitor the headlamp PCBA temperatures with NTC thermistors to thermally derate LED functions current to... 玉洁 金
18:45 功能 #2567 (已关闭): Ford_SYSR：FS_REQ0047_V1 LED Thermal Derating
The LDM shall control the LED junction temperature by controlling the current to the LED via peak current derating. I... 玉洁 金
18:43 功能 #2566 (已关闭): Ford_SYSR：FS_REQ0046_V1 Fan Failure Detection
According to the content of the configuration parameter ‘Fan_Outage_Detect_cfg’, the LDM will either perform full sta... 玉洁 金
18:41 功能 #2565 (已关闭): Ford_SYSR：FS_REQ0045_V2 Activation of the Fan
The activation of FAN can be configured by the parameter ‘FAN_Activation_Trigger_cfg’.
• 0x00: No FAN
• 0x01:Activa... 玉洁 金
18:40 功能 #2564 (已关闭): Ford_SYSR：FS_REQ0044_V1 FAN Functional self-test when power on
After power on of the LDM, the fan will be activated for specific amount of time to do the functional test.The time c... 玉洁 金
18:40 功能 #2563 (已关闭): Ford_SYSR：FS_REQ0043_V2 Bin Class Current Setting
BIN current can be set for BIN0 to BIN7 of each channel in the configuration parameter file, the current range should... 玉洁 金
18:38 功能 #2562 (已关闭): Ford_SYSR：FS_REQ0042_V2 Binning Resistor
The LDM shall be capable of supporting a binning resistor input for each channel to set the current for the correspon... 玉洁 金
18:35 功能 #2561 (已关闭): Ford_SYSR：FS_REQ0041_V2 Channel output intensity Smooth Fading
No ramping is required between 0 and 5%, 8 bit resolution is required. A non-linear ramp per Steven’s Power Law shall... 玉洁 金
18:33 功能 #2560 (已关闭): Ford_SYSR：FS_REQ0040_V1 Light Source Activation Latency Times
The LDM shall be capable of activating each function within the times provided below. Latency time refers to activati... 玉洁 金
18:30 功能 #2559 (已关闭): Ford_SYSR：FS_REQ0039_V2 Fading Requirements

| |Channel 1 |Channel 2 |Channel 3 |Channel 4 |LSD1&2|
|Fade-in capability from 0% onwards |Yes |Yes |Yes |Yes... 玉洁 金
18:27 功能 #2558 (已关闭): Ford_SYSR：FS_REQ0038_V3 Welcome/Farewell Fade Activation Signals
The Welcome/Farewell activation shall be triggered by the LIN command ‘WFSubstate’ in both ‘BCM_E_FC1’ and‘BCM_E_FC2’... 玉洁 金
18:24 功能 #2557 (已关闭): Ford_SYSR：FS_REQ0037_V1 PWM channel Welcome/Farewell Activation
PWM channels shall be also capable to be used during Welcome/Farewell sequence, according to above ‘PWMx_Function_Ass... 玉洁 金
18:23 功能 #2556 (已关闭): Ford_SYSR：FS_REQ0036_V2 DRL Welcome/Farewell Activation
When the LDM is triggered to fade on for embrace, the LDM shall fade from 0% to the duty cycle given by ‘DRL_Embrace_... 玉洁 金
18:22 功能 #2555 (已关闭): Ford_SYSR：FS_REQ0035_V1 Static Bending Light Activation
The static bending light (SBL) will be activated based on steering wheel angle provided by the Signal ‘SteAngle’ and ... 玉洁 金
18:22 功能 #2554 (已关闭): Ford_SYSR：FS_REQ0034_V1 Side marker Activation
The activation/deactivation of side marker light shall be triggered by BCM LIN command ‘Position_Park_Left/Right_Cmd’... 玉洁 金
18:21 功能 #2553 (已关闭): Ford_SYSR：FS_REQ0033_V1 Cornering Activation
The activation/deactivation of cornering light shall be triggered by BCM LIN command ‘Cornering_cmd’ with the LDM sid... 玉洁 金
18:20 功能 #2552 (已关闭): Ford_SYSR：FS_REQ0032_V1 Front Fog Activation
The activation/deactivation of front fog light shall be triggered by BCM LIN command ‘Front_Fog_Request’.
‘Front_F... 玉洁 金
18:20 功能 #2551 (已关闭): Ford_SYSR：FS_REQ0031_V2_Licoln Lit Star Activation
The activation/deactivation of Licoln Star shall be triggered by BCM LIN command ‘Position_Park_Left/Right_Cmd’ with ... 玉洁 金
18:19 功能 #2550 (已关闭): Ford_SYSR：FS_REQ0030_V1 DRL Response to Flash-To-Pass Activation
If the DRL is active, and flash to pass signal is received via LIN and IGN is either run or start, the LDM shall foll... 玉洁 金
18:06 功能 #2548 (已关闭): Ford_SYSR：FS_REQ0028_V1 DRL Response to Low Beam outage
DRL maybe affected by LB if LB outage is detected and configured to be turned off, a configurable parameter “DRL_LB_O... 玉洁 金
18:06 功能 #2547 (已关闭): Ford_SYSR：FS_REQ0027_V1 DRL EEL LIN command Table
The output of the dedicated LIN controlled DRL/Position function shall be determined based on the following LIN signa... 玉洁 金
18:03 功能 #2546 (已关闭): Ford_SYSR：FS_REQ0026_V2 DRL Control Strategy
The module will be capable of determining DRL state by either BCM LIN or by BCM ‘L/RF_DRL_LAMP_Ckt’ direct wire.
... 玉洁 金
18:02 功能 #2545 (已关闭): Ford_SYSR：FS_REQ0025_V3 Turn Indicator Feedback
Under normal operating conditions, the LDM shall report Turn indicator status to the BCM by outputting the received s... 玉洁 金
18:01 功能 #2544 (已关闭): Ford_SYSR：FS_REQ0024_V1 Turn Indicator Delay
The LDM shall support a configurable delay time of the turn indicator to be able to synchronize with other turn indic... 玉洁 金
18:01 功能 #2543 (已关闭): Ford_SYSR：FS_REQ0023_V3 Turn Indicator Activation
For the definition of the operational state of the Turn Indicator, the voltage level of the Turn supply terminal of t... 玉洁 金
17:59 功能 #2542 (已关闭): Ford_SYSR：FS_REQ0022_V2 High Beam EEL Front Fog Activation Reaction
The parameter ‘HB_combined_Front_fog_cfg’ describes the handling of HB deactivation in case of front fog activation. ... 玉洁 金
17:58 功能 #2541 (已关闭): Ford_SYSR：FS_REQ0021_V1 High Beam EEL LIN Flash-to-Pass Activation
In the event the LIN signal ‘FTP_Status’ transitions from ‘0’ to ‘1’, the high beam output(s) shall activate immediat... 玉洁 金
17:57 错误 #2515 (已解决): 需求确认
盛炜 朱
17:56 错误 #2515: 需求确认
!
!clipboard-202410241756-fie2e.png!
! 盛炜 朱
14:17 错误 #2515 (已关闭): 需求确认
当我配置LB_ Failure_Report_cfg/HB_ Failure_Report_cfg/DRL_ Failure_Report_cfg都为disable的时候，APINF2和APINFO3是否都需要置一，现在有个这个问题，... 传鹏 胡
17:57 功能 #2540 (已关闭): Ford_SYSR：FS_REQ0020_V1 High Beam LDM standard ramping
The LDM shall also have the option to select a standard LDM ramping time within parameters. To do this the parameter ... 玉洁 金
17:56 功能 #2539 (已关闭): Ford_SYSR：FS_REQ0019_V1 High Beam (HB) HCM EEL LIN Activation(Not in LDM4 scope)
In FNV2 HCM configuration the corresponding HCM HB commands will also activate the HB and/or HB2 as requested by ‘LDM... 玉洁 金
17:55 功能 #2538 (已关闭): Ford_SYSR：FS_REQ0018_V1 High Beam (HB) BCM EEL LIN Activation
High beam (of any type) shall only activate if IGN is in Run or Start.
The high beam function shall be capable of ... 玉洁 金
17:54 功能 #2537 (已关闭): Ford_SYSR：FS_REQ0017_V2 LB Activation
For the definition of the operational state of the LB, the voltage level of the LB supply terminal of the BCM (‘L/RF_... 玉洁 金
17:54 功能 #2536 (已关闭): Ford_SYSR：FS_REQ0016_V3 PWM output configuration
The LDM shall have 4 PWM outputs capable of controlling any of the following functions via configure parameter ‘PWMx_... 玉洁 金
17:53 功能 #2535 (已关闭): Ford_SYSR：FS_REQ0015_V2 Low Side Driver 1 and 2 usage Configuration
The function of the Low Side driver shall also be configurable. The low side driver activation shall then be based o... 玉洁 金
17:51 功能 #2534 (已关闭): Ford_SYSR：FS_REQ0014_V1 Low Side Driver 1 and 2 Channel Configuration
Additional secondary functions may be added any of the 4 channels (including channel 1) using one of the 2 low side d... 玉洁 金
17:49 功能 #2533 (已关闭): Ford_SYSR：FS_REQ0013_V1 Channel 2 to 4 Functional Configuration
Channel 2 to 4 shall be capable of supporting the following functions based on the parameters “Channel2/3/4_usage_cfg... 玉洁 金
17:48 功能 #2532 (已关闭): Ford_SYSR：FS_REQ0012_V1 DRL Failsafe Mode
The input will be active in BCM failsafe mode, and only under DRL hardwire control condition, the DRL and all corresp... 玉洁 金
17:45 功能 #2531 (已关闭): Ford_SYSR：FS_REQ0011_V3 Turn Indicator Failsafe Mode
The input will be active in BCM failsafe mode, and therefore the TI and all corresponding main functions of the TI sh... 玉洁 金
17:43 功能 #2530 (已关闭): Ford_SYSR：FS_REQ0010_V1 Channel 1 Failsafe Mode
The channel1 input will be active in BCM failsafe mode, and LB and all corresponding main functions of the LB shall b... 玉洁 金
17:39 功能 #2529 (已关闭): Ford_SYSR：FS_REQ0009_V1 Channel 1 output Assignment
The high side assignment of channel 1 must be base low beam in all cases. This shall not be configurable via LDM para... 玉洁 金
17:38 功能 #2528 (已关闭): Ford_SYSR：FS_REQ0008_V1 Side Detection
The LDMs will be used on a single LIN bus and needs to have defined mounting position information. To keep the LDM pa... 玉洁 金
17:30 功能 #2527 (已关闭): Ford_SYSR：FS_REQ0007_V1 TI Power Mode
Power for Turn indicator prefer to be apply to the “Power Supply Channel 3” input.
In the case channel 3 is sourced... 玉洁 金
17:29 功能 #2526 (已关闭): Ford_SYSR：FS_REQ0006_V1 DRL/PO Power supply
DRL/PO input can be supplied with two different modes:
1) a PWM signal from BCM direct wire ‘L/RF_DRL_LAMP_Ckt’ to p... 玉洁 金
17:28 功能 #2525 (已关闭): Ford_SYSR：FS_REQ0005_V1 Channel 2(Main) Power Mode
Channel 2 input (Main Power Feed) will be supplied with a steady state power supply from the vehicle to be considered... 玉洁 金
17:26 功能 #2524 (已关闭): Ford_SYSR：FS_REQ0004_V1 Channel 1 Power Mode
The LDM Channel 1 output shall be triggered by BCM Low Beam Circuit(L/RF_Low_Beam_Ckt) as described in Figure 3.
A... 玉洁 金
17:24 功能 #2523 (已关闭): Ford_SYSR：FS_REQ0003_V2 Channel power source Configuration

|Channel No. |Channelx_ Power_Source_cfg|
|Channel 1 |BCM LB (L/RF-Low_Beam_Ckt)|
|Channel 2 |Relay connected to... 玉洁 金
17:03 功能 #2522 (已关闭): Ford_SYSR：FS_REQ0002_V1 LDM Input Transients
The LDM will be expected to withstand input transients described by:
• FMC1278 - Electromagnetic Compatibility Spec... 玉洁 金
16:03 功能 #2520 (已关闭): Ford_SYSR: FS_REQ0001_V2 LDM Input
The LDM will use Channel2 as main power input as HS REQ005, and rest channels input to be used as an input signal to ... 斌 徐
15:58 功能 #2519 (已关闭): Ford_SYSR: System Requirement
-FS_LDM Localization_V2.0.docx-
FS_LDM Localization_V2.6.docx
HS_LDM Localization_V2.2.docx 斌 徐
14:54 Task #2516 (已关闭): Ford_SWET: Static code analysis
Application software Static code analysis(S00071691.7) 斌 徐

2024-10-23

16:53 Bug #2514 (Bug-已关闭): HB呼吸问题
HB的Fade speed配置为slow（4000ms），实际没有4000ms 传鹏 胡
16:11 Bug #2513 (Bug-问题回归验证): 单元测试测试问题反馈
1.app_dpl 代码最后存在PWM重复赋值计算，需删除
2.app_fan fan状态为error时，fan赋值错误，未停止fan，需分析修改 槐 杨
16:04 Task #2509: Ford_SWET: DV&PV Software Test
完成A001.6版本单元测试，静态测试，LIN一致性测试及报告更新
等待A001.8版本发布 槐 杨
15:59 Bug #2512 (Bug-已关闭): 工厂模式在有app，boot和dataset的时候，刷app后，dataset会被冲掉变成空白
在工厂模式下，有BOOT，APP,dataset的时候，再次刷写APP，原先的dataset会被冲掉，在读dataset的版本会变成空白 传鹏 胡
15:49 Bug #2511 (Bug-已关闭): 退出低功耗模式无法正常点灯
电源上电，不给任何逻辑，进入低功耗，在上任意逻辑，对应功能点不亮 传鹏 胡

2024-10-22

10:30 Task #2510 (进行中): Ford_Fusa: function Safety SSR
Complete and sign Fusa SSR documents with Ford team 斌 徐
10:28 Task #2509 (已关闭): Ford_SWET: DV&PV Software Test
Ford LDM Function Test 斌 徐
10:26 Task #2508 (已关闭): Ford_SWED: DV&PV Software Release
Release Software for DV/PV test:
Boot loader Software Version：SW0007170.B001
Application Software Version：SW0007169... 斌 徐
 

导出 Atom