玉洁 金 的活动
从 2024-10-28 到 2024-11-06
2024-11-05
- 13:50 FORD LDM Localization 功能 #3029 (已关闭): Ford_SWER_ REQ26-REQ30_0009：DRL_activation_time_after_deact_cfg for dataset
- ‘DRL_activation_time_after_deact_cfg’need to be selected in the dataset.
Range: 0ms to 1000ms; Resolution: 100ms - 13:48 FORD LDM Localization 功能 #3028 (已关闭): Ford_SWER_ REQ26-REQ30_0008：DRL Response to Flash-To-Pass Activation
- Precondition：If the DRL is active, and flash to pass signal is received via LIN and IGN is either run or start;
‘DRL... - 13:29 FORD LDM Localization 功能 #3027 (已关闭): Ford_SWER_ REQ26-REQ30_0007：DRL Response to Turn Indicator Activation
- ‘LSDx_usage_cfg’<>0x03, use 1 DRL behavior;‘LSDx_usage_cfg’=0x03, use 2 DRL behavior;
!clipboard-202411051329-wa1tc.... - 13:26 FORD LDM Localization 功能 #3026 (已关闭): Ford_SWER_ REQ26-REQ30_0006：DRL Response to Low Beam outage
- “DRL_LB_Outage_cfg”need to be selected in the dataset,it determines if DRL is affected by LB outage.
!clipboard-... - 13:05 FORD LDM Localization 功能 #3024 (已关闭): Ford_SWER_ REQ26-REQ30_0005：Output duty cycle for dataset
- ‘DRL_Intensity_cfg’ should be 100% as default value，does not require configuration.
‘ParkPos_Intensity_cfg’can be se... - 12:57 FORD LDM Localization 功能 #3023 (已关闭): Ford_SWER_ REQ26-REQ30_0004：DRL BCM LIN
- DRL request shall take a higher priority than Position request
|DRL_Rqst |Position_Park_Left_Cmd |Position_Park_Rig... - 10:51 FORD LDM Localization 功能 #3022 (已关闭): Ford_SWER_ REQ26-REQ30_0003：DRL direct wire control
- 1、If BCM DRL direct wire duty cycle >= “DRL_POS_TriggerDC_cfg”, it should be DRL intensity,
2、If 5% <= BCM DRL dire... - 10:27 FORD LDM Localization 功能 #3021 (已关闭): Ford_SWER_ REQ26-REQ30_0002： Accuracy and Frequency - Dataset
- “DRL_POS_Trigger_DutyCycle_cfg” need to be selected in the dataset
Values range between 10-41%, 200Hz（If DRL input f... - 10:16 FORD LDM Localization 功能 #3020 (已关闭): Ford_SWER_ REQ26-REQ30_0001： DRL Control Strategy - Dataset
- 1、BCM LIN
2、BCM ‘L/RF_DRL_LAMP_Ckt’ direct wire - 10:06 FORD LDM Localization 功能 #3019 (已关闭): Ford_SYSR：Daytime Running Lamp (DRL)/Park Lamp Drive Mode Activation
- REQ26
The module will be capable of determining DRL state by either BCM LIN or by BCM ‘L/RF_DRL_LAMP_Ckt’ direct wir... - 09:29 FORD LDM Localization 功能 #3018 (已关闭): Ford_SWER_0029_0001：DRL Response to Turn Indicator Activation
- 1、‘DRL_activation_time_after_deact_cfg’：Range: 0ms to 1000ms; Resolution: 100ms
2、‘LSDx_usage_cfg’<>0x03, use 1 DRL ... - 08:57 FORD LDM Localization 功能 #3017 (已关闭): Ford_SYSR：FS_REQ0029_V1 DRL Response to Turn Indicator Activation
- In EEL LIN systems, the LDM shall take the configured performance control action when the TI is activated on the same...
2024-11-01
- 14:55 FORD LDM Localization 功能 #3009 (已关闭): Ford_SWER_003x_0002：Welcome/Frawell for App
- App read the value of “Embrace_Delay_Welcome/Farewell_cfg”
It represents the time the LDM shall begin the fade after... - 14:51 FORD LDM Localization 功能 #3008 (已关闭): Ford_SWER_003x_0001：Welcome/Frawell for dataset
- ‘Embrace_Delay_Welcome_cfg’ can be seleted in the dataset
“Embrace_Delay_Welcome/Farewell_cfg”parameter definition:... - 13:36 FORD LDM Localization 功能 #3007 (已关闭): Ford_SWER_0026_0004：DRL frequency
- If DRL input frequency>210Hz||<190Hz,software should ignore this PWM.
- 13:11 FORD LDM Localization 功能 #3005 (已关闭): Ford_SYSR：FS_REQ003x_V1 Welcome/Frawell
- The LDM shall support Fade on/off animation, ‘Embrace_Delay_Welcome_cfg/Embrace_Delay_farewell_cfg’ describes the tim...
2024-10-31
- 18:31 FORD LDM Localization 功能 #3004 (已关闭): Ford_SWER_0027_0002：DRL EEL LIN command Table for dataset
- ‘DRL_Intensity_cfg’ should be 100% as default value.
‘ParkPos_Intensity_cfg’can be selected in the dataset - 18:25 FORD LDM Localization 功能 #3001 (已关闭): Ford_SWER_0028_0002：DRL Response to Low Beam outage for App
- App needs to read the values configured in the dataset;
1、if “DRL_LB_Outage_cfg”= 0x00, DRL will not be affected by ... - 18:16 FORD LDM Localization 功能 #2998 (已关闭): Ford_SWER_0026_0003：DRL value for App
- If BCM DRL direct wire duty cycle >= “DRL_POS_TriggerDC_cfg”, it should be DRL intensity,
If 5% <= BCM DRL direct w... - 18:03 FORD LDM Localization 功能 #2997 (已关闭): Ford_SWER_0022_0002：High Beam EEL Front Fog Activation Reaction for dataset
- 'HB_combined_Front_fog_cfg’is the fade out time of HB
Need to configured in the dataset
0x00 = Parameter to be igno... - 17:53 FORD LDM Localization 功能 #2996 (已关闭): Ford_SWER：FS_REQ0018&REQ0020_0006 High Beam LDM standard ramping for dataset
- 'LDM_internal_standard_ramping_cfg'can be configured in the dataset；
There are four options available：immediate、100m... - 17:48 FORD LDM Localization 功能 #2995 (已关闭): Ford_SWER：FS_REQ0018&REQ0020_0005 High Beam BCM EEL LIN ramping for dataset
- ‘HB_fade_fast_spd_cfg’, ‘HB_fade_med_spd_cfg’, ‘HB_fade_slow_spd_cfg’can be configured in the dataset；
The list of f... - 17:36 FORD LDM Localization 功能 #2993 (已关闭): Ford_SWER_0045_0006：NTC Temperatur Triggle Fan For App
- App reads the value of ‘Fan_Activation_Temp_cfg’ ,
If ‘FAN_Activation_Trigger_cfg’ = 0x03 ,FAN will be activated wh... - 17:32 FORD LDM Localization 功能 #2992 (已关闭): Ford_SWER_0045_0005：NTC Source Triggle Fan For App
- If ‘FAN_Activation_Trigger_cfg’ = 0x03 ,
App reads the value of ‘FAN_Activation_NTC_cfg’
if ‘FAN_Activation_NTC_cfg... - 17:28 FORD LDM Localization 功能 #2991 (已关闭): Ford_SWER_0045_0004：Activation of the Fan For App
- App reads the value of 'FANphotoactivation_Trigger_cfg'
if 'FANphotoactivation_Trigger_cfg'= 0x00, Always Deactivat... - 17:19 FORD LDM Localization 功能 #2989 (已关闭): Ford_SWER：FS_REQ0018&REQ0020_0006 High Beam LDM standard ramping for App
- If APP read the value of 'HB_Ramping_method_cfg' in the dataset is selected as *LDM* , the fade speed will be issued ...
- 17:14 FORD LDM Localization 功能 #2987 (已关闭): Ford_SWER：FS_REQ0018&REQ0020_0005 High Beam BCM EEL LIN ramping for App
- If APP read the value of 'HB_Ramping_method_cfg' in the dataset is selected as *BCM EEL LIN BCM* ,the fade speed will...
- 17:10 FORD LDM Localization 功能 #2984 (已关闭): Ford_SWER：FS_REQ0018&REQ0020_0004 High Beam channel
- HB channel: The APP reads the generated data from the Dataset. If Channel2/3/4_usage_cfg is 0x02,The corresponding ch...
- 17:01 FORD LDM Localization 功能 #2983 (已关闭): Ford_SWER：FS_REQ0018&REQ0020_0003 High Beam control mode for dataset
- ‘HB_Ramping_method_cfg’can be selected in the dataset（BCM EEL LIN BCM or LDM）
0x00: follow BCM LIN activation, ref... - 16:59 FORD LDM Localization 功能 #2982 (已关闭): Ford_SWER：FS_REQ0018&REQ0020_0002 High Beam ramping accuracy and frequency
- Accuracy：between 0% and 100%， 1% per step
PWM Frequency：200HZ - 16:56 FORD LDM Localization 功能 #2981 (已关闭): Ford_SWER：FS_REQ0018&REQ0020_0001 High Beam activate condition
- High beam (of any type) shall only activate if IGN is in Run or Start
- 16:52 FORD LDM Localization 功能 #2980 (已关闭): Ford_SYSR：FS_REQ0018&REQ0020_V1 High Beam
- *REQ0018 High Beam (HB) BCM EEL LIN Activation*
High beam (of any type) shall only activate if IGN is in Run or Star... - 10:03 FORD LDM Localization 功能 #2971 (已关闭): Ford_SWER_0004_0002： LB Additional channel Power Mode
- Additional channels assigned to LB must receive power from the main power supply.
- 10:00 FORD LDM Localization 功能 #2969 (已关闭): Ford_SWER_0004_0001： Channel 1 Power Mode
- !clipboard-202410310958-qmddq.png!
The LDM Channel 1 shall be powered by BCM Low Beam Circuit(L/RF_Low_Beam_Ckt) - 09:09 FORD LDM Localization 功能 #2858: Ford_SWER_0026_0001：DRL Control Mode for dataset
- #2630
- 09:07 FORD LDM Localization 功能 #2858: Ford_SWER_0026_0001：DRL Control Mode for dataset
- #2614
#2906
#2907
2024-10-30
- 16:15 FORD LDM Localization 功能 #2917: Ford_SWER_0020_0003：HB ramping trigger mode
- #2952 and #2826
- 10:53 FORD LDM Localization 功能 #2917 (已关闭): Ford_SWER_0020_0003：HB ramping trigger mode
- 1、LIN BCM；
If the value of 'HB-Ramping_method_cfg' in the configuration is selected as BCM EEL LIN BCM,the fade spee... - 16:12 FORD LDM Localization 功能 #2827: Ford_SWER_0020_0002：High Beam LDM standard ramping -‘HB_Ramping_method_cfg’
- #2952 and #2826
- 16:09 FORD LDM Localization 功能 #2826: Ford_SWER_0020_0001：High Beam LDM standard ramping
- ‘HB_Ramping_method_cfg’can be selected in the configuration（BCM EEL LIN BCM or LDM）refer to #2952
- 15:52 FORD LDM Localization 功能 #2952: Ford_SWER_0018_0004： High Beam (HB) BCM EEL LIN ramping
- ‘HB_Ramping_method_cfg’can be selected in the configuration（BCM EEL LIN BCM or LDM）refer to #2540
- 15:50 FORD LDM Localization 功能 #2952 (已关闭): Ford_SWER_0018_0004： High Beam (HB) BCM EEL LIN ramping
- If the value of 'HB-Ramping_method_cfg' in the configuration is selected as BCM EEL LIN BCM,the fade speed will be is...
- 15:27 FORD LDM Localization 功能 #2821: Ford_SWER_0018_0003：High Beam (HB) BCM EEL LIN Activation dataset-HB channel
- 1、HB channel refer to #2643
- 13:08 FORD LDM Localization 功能 #2818: Ford_SWER_0018_0002： High Beam (HB) ramping accuracy and frequency
- #2540
- 12:55 FORD LDM Localization 功能 #2905: Ford_SWER_0017_0002：LB Activation restriction
- #2529
- 12:50 FORD LDM Localization 功能 #2905: Ford_SWER_0017_0002：LB Activation restriction
- #2610
- 12:45 FORD LDM Localization 功能 #2925 (已关闭): Ford_SWER_0017_0003：LB additional channels
- Any additional channels assigned to Low Beam should also activate based on this signal.
2024-10-29
- 16:52 FORD LDM Localization 功能 #2905 (已关闭): Ford_SWER_0017_0002：LB Activation restriction
- The output of channel 1 should always be applied to Main LB and no other function
- 15:26 FORD LDM Localization 功能 #2897 (已关闭): Ford_SWER_0033_0001：Cornering Activation
- The activation/deactivation of cornering light shall be triggered by BCM LIN command ‘ *Cornering_cmd* ’
signal def... - 14:29 FORD LDM Localization 功能 #2878 (已关闭): Ford_SWER_0028_0001：DRL Response to Low Beam outage for dataset
- “DRL_LB_Outage_cfg” will determine if DRL is affected by LB outage(0x00、0x01、0x02)
Need to select the value of “DRL_... - 14:04 FORD LDM Localization 功能 #2868 (已关闭): Ford_SWER_0027_0001：DRL EEL LIN command Table for App
- DRL request shall take a higher priority than Position request
|DRL_Rqst |Position_Park_Left_Cmd |Position_Park_Rig... - 13:58 FORD LDM Localization 功能 #2865 (已关闭): Ford_SWER_0026_0002：DRL value for dataset
- The value of “DRL_POS_TriggerDC_cfg” needs to be selected in the Dataset
“DRL_POS_TriggerDC_cfg”value range between ... - 13:41 FORD LDM Localization 功能 #2858 (已关闭): Ford_SWER_0026_0001：DRL Control Mode for dataset
- The trigger source for DRL/PO function needs to be set in the Dataset
1、BCM LIN
2、BCM ‘L/RF_DRL_LAMP_Ckt’direct w... - 12:48 FORD LDM Localization 功能 #2841 (已关闭): Ford_SWER_0022_0001：High Beam EEL Front Fog Activation Reaction for App
- 1、if App read the value of ‘HB_combined_Front_fog_cfg’= 0，activate/deactivate HB as specified；Fog is not related to H...
- 12:24 FORD LDM Localization 功能 #2829 (已关闭): Ford_SWER_0021_0002 ：FTP priority
- FTP status shall always take priority over normal high beam activation
- 12:23 FORD LDM Localization 功能 #2828 (已关闭): Ford_SWER_0021_0001：High Beam EEL LIN Flash-to-Pass Activation
- 1、the LIN signal ‘FTP_Status’ transitions from ‘0’ to ‘1’, the high beam output(s) shall *activate immediately* ；
2、... - 11:52 FORD LDM Localization 功能 #2827 (已关闭): Ford_SWER_0020_0002：High Beam LDM standard ramping -‘HB_Ramping_method_cfg’
- ‘HB_Ramping_method_cfg’can be selected in the configuration（BCM EEL LIN BCM or LDM）
0x00: follow BCM LIN activatio... - 11:48 FORD LDM Localization 功能 #2826 (已关闭): Ford_SWER_0020_0001：High Beam LDM standard ramping
- If the value of 'HB_Ramping_method_cfg' in the configuration is selected as LDM, the fade speed will be issued by 'LD...
- 11:30 FORD LDM Localization 功能 #2821 (已关闭): Ford_SWER_0018_0003：High Beam (HB) BCM EEL LIN Activation dataset-HB channel
- HB channel: The APP reads the generated data from the Dataset. If Channel2/3/4_usage_cfg is 0x02,The corresponding ch...
- 11:21 FORD LDM Localization 功能 #2818 (已关闭): Ford_SWER_0018_0002： High Beam (HB) ramping accuracy and frequency
- Accuracy：between 0% and 100%
PWM Frequency：200HZ
For specific methods, please refer to FS_REQ0020_V1 High Beam LDM ... - 11:04 FORD LDM Localization 功能 #2804 (已关闭): Ford_SWER_0018_0001： High Beam (HB) BCM EEL LIN activate condition
- 1、High beam (of any type) shall only activate if *IGN is in Run or Start* ;
2、Issue *HB activation command*:LIN comm... - 10:35 FORD LDM Localization 功能 #2787 (已关闭): Ford_SWER_0017_0001：LB Activation conditions
- The voltage level of the LB supply terminal of the BCM (‘L/RF_Low_Beam_Ckt’) must be used
- When "voltage" >= 7V, L...
导出 Atom